Arduino

SKU: SF-CAB-11301 | Brand: SparkFun

A 6-foot (1.8 m) USB 2.0 cable with a Type-A plug on one end and a Mini-B 5-pin plug on the other. Use it to connect cameras, USB hubs, FTDI programmers, LiPo chargers, and other devices that use the Mini-B connector....

SKU: AF-3104 | Brand: Adafruit

This Mini Illuminated Momentary Power Button it an adorable breadboard-friendly tactile switch that has a built-in LED. It provides a simple way to add a tactile switch and a colorful universal power symbol to...

SKU: SF-SEN-13285 | Brand: SparkFun

This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.This unit works great from 5...

SKU: SF-WRL-13287 | Brand: SparkFun

The SparkFun ESP8266 WiFi Shield is an Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. There are a variety of designs based around the ...

SKU: SF-SEN-13266 | Brand: SparkFun

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by ...

SKU: SF-BOB-13263 | Brand: SparkFun

Introducing the 3.3V SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino board...

SKU: AF-255 | Brand: Adafruit

THIS IS THE LATEST VERSION 2.1The ChronoDot RTC is an extremely accurate real time clock module, based on the DS3231 temperature compensated RTC (TCXO). It includes a CR1632 battery, which should last at least 8 years...

SKU: AF-3200 | Brand: Adafruit

The Teensy 3.x Feather Adapter rearranges the pins of a Teensy 3.x board to match the Adafruit Feather form factor and pinout. This allows the Teensy to work with the full range of FeatherWing add-ons — motor drivers,...

SKU: AF-374 | Brand: Adafruit

These 1-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontro...

SKU: DF-ROB0112 | Brand: DFRobot

DFRobot proudly presents Devastator Tank Mobile Platform, our newest track mobile robot platform. It is fully compatible with most popular controllers in the market such as Arduino, Raspberry Pi and so on. ...

SKU: AF-409 | Brand: Adafruit

Electroluminescent (EL) wire produces a beautiful aqua (blue-green) glow that looks like thin neon lighting. This high-brightness version uses the latest technology and is twice as bright as standard 2.3mm EL wire, em...

SKU: DF-ROB0117 | Brand: DFRobot

The Cherokey 4WD Basic Arduino Robot Kit is a perfect wheeled robot platform to build your own robot and to get started with Arduino Robot. With just a few simple steps of assembling the hardware and tuning the...

SKU: DF-SEN0162 | Brand: DFRobot

The Gravity Analog UV Sensor V2 uses a GUVA-S12SD photodiode to detect ultraviolet radiation in the 200–370 nm (UV-A) wavelength range. It outputs a linear analogue voltage signal proportional to UV intensity, making ...

SKU: SF-PRT-13010 | Brand: SparkFun

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

SKU: DF-DFR0359 | Brand: DFRobot

INTRODUCTION eClip is an innovative programming/testing tool specially designed for Makers. It solves the problem of prototyping wearable projects with ICSP and FTDI interfaces in limited spa...

SKU: SF-BOB-12941 | Brand: SparkFun

With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding a...

SKU: SF-DEV-12924 | Brand: SparkFun

The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not on...

SKU: SF-COM-10613 | Brand: SparkFun

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mech...

SKU: DF-DFR0376 | Brand: DFRobot

INTRODUCTION OCELL is a 0.5" micro OLED display designed for Arduino and other microcontrollers. This micro OLED display is small as the grown-up's fingernail- 0.5" only. It has 450cd/m^2 sc...

SKU: SF-COM-12792 | Brand: SparkFun

This is a 2x40 pin right-angle PTH header. This header can be broken apart with a fair amount of force to form smaller header formations. Don’t worry, it’s easy enough to break it where you need! Each pin has a spa...