Arduino

SKU: SF-COM-00097 | Brand: SparkFun

We use these little buttons on everything! These Miniature Single Pole Single Throw switches have a good click to them and are breadboard friendly. Perfect as a tactile reset switch. These buttons are rated up to 5...

SKU: DF-DFR0282 | Brand: DFRobot

The Beetle is one of the smallest Arduino Leonardo-compatible boards available, built around the ATmega32U4 microcontroller running at 16MHz. Despite its tiny size, it delivers the full functionality of an Arduino Leo...

SKU: DF-SER0006 | Brand: DFRobot

A lightweight 9g micro servo with 1.6 kgf·cm of torque at 4.8V. Ideal for small-scale robotics, beam robots, and automation tasks where a compact, affordable servo is needed. At only 9 grams, it fits into tight spaces...

SKU: EC-ELE18716S | Brand: Elecrow

A comprehensive 300+ piece electronics component kit for getting started with Arduino, Raspberry Pi, and general electronics prototyping. Everything is packed into a single box for organised, efficient access — coveri...

SKU: DF-DFR0339 | Brand: DFRobot

Bluno Beetle - The smallest Arduino Board is another milestone in wearable electronics device area based arduino uno, which makes DIY users have more options in the project design. It is fully compatible with Bluno...

SKU: DF-SEN0308 | Brand: DFRobot

The Gravity Analogue Waterproof Capacitive Soil Moisture Sensor from DFRobot measures soil moisture using capacitive sensing rather than resistive probes, offering significantly better corrosion resistance and longer ...

SKU: AF-3814 | Brand: Adafruit

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST...

SKU: DF-SEN0161 | Brand: DFRobot

You may check the latest version - Gravity: Analog pH Sensor/Meter Kit V2 to meet your requirements and Liquid Sensor Selection Guide to get better familiar with our liquid sensor series.Need to measure water quality...

SKU: SF-DEV-11061 | Brand: SparkFun

The Arduino Mega 2560 R3 is a microcontroller board based on the ATmega2560, offering significantly more I/O than standard Arduino boards. With 54 digital I/O pins, 16 analog inputs, and 4 hardware serial ports, it's ...

SKU: DF-SEN0539-EN | Brand: DFRobot

What is voice recognition?  Voice recognition is a computer technology that recognizes and converts speech signals into editable text or operational commands through analysis. It allows people to interact with...

SKU: DF-DFR0140 | Brand: DFRobot

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. It can be either powered from 6-12...

SKU: EC-MCS02930M | Brand: Elecrow

This Adruino compatible motor Driver shield is a full-featured products that it can be used to drive 4 DC motor or two 4-wire stepper and two 5v servo. It drive the DC motor and stepper with the L293D,and it drive ...

SKU: SF-COM-09181 | Brand: SparkFun

It’s the end of the world, and you need a button to press. This is it. A 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a pre-installed long life horizontal micro...

SKU: DF-SEN0137 | Brand: DFRobot

DHT22 capacitive humidity sensing digital temperature and humidity module is one that contains the compound has been calibrated digital signal output of the temperature and humidity sensors. Application of a dedicate...

SKU: AF-3297 | Brand: Adafruit

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applic...

SKU: AF-3351 | Brand: Adafruit

Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like this speaker as it is small...

SKU: AF-3955 | Brand: Adafruit

This 200 mm cable converts a JST PH 4-pin connector into four individual wires with 0.1″ (2.54 mm) male header pins on the end. It's designed for connecting STEMMA and Grove I²C boards to breadboards, socket headers, ...

SKU: DF-DFR0229 | Brand: DFRobot

This is a Micro SD(TF) module from DFRobot. It is compatible with TF SD card (commonly used in Mobile Phone) which is the most tiny card in the market. SD module has various applications such as data logger, au...

SKU: AF-3006 | Brand: Adafruit

The Adafruit MAX98357A I2S Class D Amplifier Breakout is an all-in-one digital audio solution that decodes I2S audio and amplifies it directly to a speaker — no separate DAC required. Delivering up to 3.2W into a 4Ω s...

SKU: AF-373 | Brand: Adafruit

This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboar...