Arduino Shields

SKU: AF-2866 | Brand: Adafruit

Put on your sunglasses before plugging in this shield — 40 eye-blistering RGBW LEDs adorn the NeoPixel Shield for a blast of configurable colour and white. Arranged in a 5×8 matrix, each pixel is individually addressa...

SKU: AF-2865 | Brand: Adafruit

Put on your sunglasses before plugging in this shield — 40 eye-blistering RGBW LEDs adorn the NeoPixel Shield for a blast of configurable colour and white. Arranged in a 5×8 matrix, each pixel is individually addressa...

SKU: SF-GPS-15136 | Brand: SparkFun

With GPS you are able to know where you are, where you’re going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GPS Real Time Kinematics (RTK) has mastered dia...

SKU: SF-DEV-09627 | Brand: SparkFun

Developed by Dave Vondle and IDEO Labs, this board is essentially the same as our Power Driver Shield, but the through-hole parts have been switched out for smaller SMD construction, allowing you to to drive high-curr...

SKU: SF-DEV-11287 | Brand: SparkFun

The Arduino WiFi Shield allows an Arduino board to connect to the internet using the 802.11 wireless specification (WiFi). It is based on the HDG204 Wireless LAN 802.11b/g System in-Package. An Atmega 32UC3 provides a...

SKU: AF-1651 | Brand: Adafruit

The 2.8" TFT Touch Shield with Resistive Touch Screen plugs directly into any Arduino UNO or Mega-shaped board, providing a bright, full-colour display with touch input and an onboard MicroSD card socket. Fully assemb...

SKU: SF-COM-11041 | Brand: SparkFun

A bare PCB for building a relay control circuit, based on SparkFun's Controllable Power Outlet tutorial. It allows you to switch high-voltage loads using a simple 0–5V GPIO signal from any microcontroller. Components ...

SKU: SS-ELB141D1P | Brand: Seeed Studio

This is a Protoshield kit with the same connector as Electronic Brick, you can solder something onto this and use it as a regular Electronic Brick.    You will also need this cable to connect it to Se...

SKU: AF-1750 | Brand: Adafruit

The Synthetos gShield (formerly grblShield) V5 is a 3-axis CNC stepper motor driver shield for Arduino. Designed as a complete hardware companion for the grbl CNC motion control firmware, it turns an Arduino Uno into ...

SKU: AF-2024 | Brand: Adafruit

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — att...

SKU: DF-DFR0013 | Brand: DFRobot

The DFRobot IIC to GPIO Shield V2.0 (DFR0013) expands your Arduino's digital I/O capacity by converting a single I2C bus into 16 additional digital I/O ports. Using just two data lines (SCL and SDA), the shield frees ...

SKU: PL-2508 | Brand: Pololu

This shield makes it easy to build an Arduino-controlled Zumo robot. The shield mounts onto an assembled Zumo chassis, connecting directly to the chassis’s battery terminals and motors, and the Arduino plugs into ...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: AF-2653 | Brand: Adafruit

Get your Particle (formally known as Spark) Photon moving with a PhoBot Robotics shield. No, this is not a robot that makes you a delicious bowl of Vietnamese soup.  Instead, it's a board from Simon Monk ...

SKU: DF-DFR0174 | Brand: DFRobot

The XBee USB Adapter V2 is an update version from DFRobot. It features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The Atmega8U2 firmware uses the standard USB ...

SKU: SF-DEV-14285 | Brand: SparkFun

The SparkFun Wireless Motor Driver Shield is designed to make connecting motors, sensors and other components to your Arduino-based project as fast and easy as possible. The heart of the Wireless Motor Driver Shield i...

SKU: SF-KIT-14180 | Brand: SparkFun

Robots are fun, and Arduinos are easy. So wouldn’t it be nice if there were a kit that included everything you need to get your Arduino device set up to control a simple two-motor-circuit buddy? The SparkFun Ardumoto ...

SKU: SF-DEV-14129 | Brand: SparkFun

The Ardumoto Shield is a dual-motor controller for Arduino based on the L298 H-bridge. It can drive two DC motors at up to 2A per channel, making it an excellent platform for RC vehicles and small autonomous robots. ...

SKU: DF-DFR0256 | Brand: DFRobot

The Mega Multi IO Expansion Shield lets you stack up to four shields simultaneously on an Arduino Mega or Due without worrying about I/O pin conflicts. All Mega I/O pins are expanded and routed to four separate shield...

SKU: DF-DFR0274 | Brand: DFRobot

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED stri...