Arduino Sensors

SKU: DF-SEN0206 | Brand: DFRobot

INTRODUCTION We can divide temperature measurement in to two types: contact and non-contact. Contact measurement can only accurately measure temperature when the testing object and the se...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...

SKU: SF-SEN-09376 | Brand: SparkFun

This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the res...

SKU: SF-COM-00299 | Brand: SparkFun

The Texas Instruments CD74HC4067 is a 16-channel analogue multiplexer/demultiplexer IC. It allows you to route one of 16 analogue signals to a single common pin (or vice versa) using just 4 digital control lines plus ...

SKU: SF-SEN-09673 | Brand: SparkFun

A compact force sensitive resistor (FSR) from Interlink Electronics with a 4 mm (0.16″) diameter active sensing area. The resistance changes based on applied pressure — from over 1 MΩ with no pressure down to approxim...

SKU: DF-DFR1132 | Brand: DFRobot

##Introduction Gravity: Linear/Analog Hall Sensor is a high-precision device designed for measuring and monitoring magnetic field strength. Advanced Hall effect circuitry at the core converts magnetic induction streng...

SKU: EF-EF04079 | Brand: ElecFreaks

Octopus TMP36 Temperature Sensor Brick is a temperature sensor with low voltage and accurate celsius read. It can provide voltage output,which forms a linear relationship with celsius temperature. TMP36 do not need an...

SKU: AF-1164 | Brand: Adafruit

This breakout board will solve all your current-monitoring problems. Instead of struggling with a multimeter, you can just use the handy INA169 chip on this breakout to both measure both the DC current draw and have a...

SKU: SF-SEN-17052 | Brand: SparkFun

The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher ...

SKU: DF-SEN0135 | Brand: DFRobot

The HRLV-MaxSonar-EZ (MB1013) is a high-resolution ultrasonic distance sensor with 1 mm resolution and a range of up to 5 metres. It features multiple output formats, internal temperature compensation, virtually no de...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...

SKU: DF-SEN0221 | Brand: DFRobot

The Hall Angle Sensor is a miniature 360 degree sensor which works based on the principle of the Hall effect. It is compatible with the DFRobot Gravity sensor interface, and works with a 5V DC power supply. The ...

SKU: DF-SEN0019 | Brand: DFRobot

This is an Arduino infrared distance sensor. It has an adjustable detection range, 3cm - 80cm. It is small, easy to use, assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line,...

SKU: SF-SEN-26092 | Brand: SparkFun

Visualise magnetic fields in real time with a dense 8x8 array of Hall-effect sensors. This tile lets you observe nearby magnets, current flow in wires and fields generated by electric motors as a live magnetic image.T...