All Products

SKU: AF-1774 | Brand: Adafruit

The 2.8" TFT Display with Resistive Touchscreen is a bare LCD module featuring 320×240 resolution with individual RGB pixel control. Driven by the ILI9341 chipset, it supports SPI (3- or 4-wire), 8-bit parallel, and 1...

SKU: AF-1789 | Brand: Adafruit

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will ...

SKU: AF-1792 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1863 | Brand: Adafruit

This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendl...

SKU: AF-1875 | Brand: Adafruit

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V de...

SKU: AF-2222 | Brand: Adafruit

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3m...

SKU: AF-2201 | Brand: Adafruit

This is just about the cutest, tiniest little micro servo we could find, even smaller than the 9 gram micro servos we love so much.  It can rotate approximately 180 degrees (90 in each direction) and works just l...

SKU: AF-2187 | Brand: Adafruit

A custom-made 2×20 short female header designed for surface-mount (SMT) Raspberry Pi HAT designs. This header provides the slimmest possible profile when you need a low-clearance connection between your HAT and a Rasp...

SKU: AF-2168 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that s...

SKU: AF-2343 | Brand: Adafruit

These APA102C (DotStar) RGB LEDs feature an integrated driver chip inside each 5050 SMD package, giving you individually addressable 24-bit colour control (8 bits each for red, green, and blue). The same smart LED use...

SKU: AF-2337 | Brand: Adafruit

Finally we get our very own super sweet sixteen... 16 millimeters that is! Our Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT or other Pi accessories w...

SKU: AF-2424 | Brand: Adafruit

This stepper motor is a little different than the large NEMA-17 types you may be used to. These are often used in gauges for motorcycles and cars to replace the old-style fully-analog type. They have extremely fine...

SKU: AF-2476 | Brand: Adafruit

Replacement silicone tubes for the Professional Silicone-Tip Solder Sucker. Cut to your desired length as needed — the elastic, heat-resistant silicone withstands temperatures up to 350°C, letting you get close to you...

SKU: AF-2473 | Brand: Adafruit

A 50 g spool of lead-free solder wire ideal for through-hole and surface-mount soldering. With a 0.5 mm diameter and no-clean rosin flux core, this wire delivers clean, reliable joints without the need for post-solder...

SKU: DF-FIT0520 | Brand: DFRobot

A 6V brushed DC motor with a 20:1 metal gearbox and an integrated quadrature encoder. The encoder provides 11 counts per revolution of the motor shaft, corresponding to 224.4 counts per revolution of the gearbox outpu...

SKU: DF-FIT0116 | Brand: DFRobot

This is a high quality Category 5 (CAT5) patch cables is the solution to your internetworking needs. DOCUMENTS Cat 5 Definition

SKU: DF-DFR0521 | Brand: DFRobot

The micro:bit Expansion Board for Boson is a carry-on board that connects to the BBC micro:bit via edge connector, replacing crocodile clips with six keyed 3-pin sockets. It is compatible with DFRobot's Boson and Grav...

SKU: SF-PRT-14311 | Brand: SparkFun

These headers are made to work with the SparkFun ESP32 Thing and ESP32 Power Control Shield boards. Each set of headers makes your ESP32 Thing easily stackable with the Power Control Shield or other applications. This...

SKU: SF-COM-09340 | Brand: SparkFun

This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. This button has a great tactile, ‘clicky’ feel.Features: Concave plunger design D...

SKU: DF-FIT0043 | Brand: DFRobot

The second version of the 9V to Barrel Jack Adapter, now featuring a hard plastic battery snap for easier connection and disconnection. Plug a 9V battery into one end and connect the other to any device with a 5.5 × 2...