All Products

SKU: AF-2789 | Brand: Adafruit

The premise of this MicroUSB to 5.5/2.1mm DC Barrel Jack Adapter is simple. There's a MicroUSB plug on one end and a 5.5mm/2.1mm DC barrel jack with center positive polarity on the other. This allows you ...

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: SF-TOL-08775 | Brand: SparkFun

Solder wick, coffee, and paper towels keep SparkFun running. You can steal someone’s diagonal cutters for a minute, but you’d better ask before touching their solder wick. Solder wick is a composed of copper threads ...

SKU: DF-FIT0290 | Brand: DFRobot

This is a SOP8 to DIP8 Adapter Board. You can change the SOP8 to DIP8 packaging.So that You needn't to buy the DIP chips for prototyping specially.Just solder the SMD chips on the board and plug it into the bread b...

SKU: SF-SEN-08712 | Brand: SparkFun

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor’s resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but th...

SKU: AF-2777 | Brand: Adafruit

This USB to DC booster cable has an integrated boost converter that steps up 5V USB power to 9V DC, output through a centre-positive 2.1 mm barrel jack. It's a convenient way to power 9V devices from any USB port — wh...

SKU: DF-SEN0068 | Brand: DFRobot

This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing lightly, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but the re...

SKU: SF-SEN-08681 | Brand: SparkFun

These are very thin variable potentiometers. By pressing down on various parts of the strip, the resistance linearly changes from 100Ohms to 10,000Ohms allowing the user to very accurately calculate the relative po...

SKU: DF-KIT0015 | Brand: DFRobot

This MiniQ motor wheel set is especially designed for education and hobbies. It features a powerful metal gear motors which provide a speedy robot. With buildin encoders, it can do PID speed control which is Ideal...

SKU: SF-PRT-08672 | Brand: SparkFun

This is a simple two wire cable. One end has a 2-pin 0.1" pitch female connector, the opposite end is stripped and tinned stranded wire. Dimensions: 120mm length

SKU: DF-FIT0294 | Brand: DFRobot

A 10-pack of M3 × 6mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cle...

SKU: DF-DFR0224 | Brand: DFRobot

The Arduino Screwless Terminal Shield breaks out all Arduino Uno-compatible header pins to spring-loaded push-in terminal blocks. Press the lever, insert your wire, and release — no screwdriver needed. The shield stac...

SKU: DF-FIT0273 | Brand: DFRobot

A 10-pack of M3 × 16mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cl...

SKU: PL-1383 | Brand: Pololu

Overview The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the ability to deliver up to several hundred Watts in ...

SKU: SF-COM-08588 | Brand: SparkFun

This is a very common signal diode - 1N4148. Use this for signals up to 200mA of current. If you need a bunch of these, you can get good bulk discounts on Digikey, part # : 1N4148FS-ND Documents: Datasheet

SKU: DF-FIT0281 | Brand: DFRobot

A 10-pack of M3 × 25mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cl...

SKU: SF-COM-08582 | Brand: SparkFun

Standard frequency crystals - use these crystals to provide a clock input to your microprocessor. Rated at 20pF capacitance and +/- 50ppm stability. Low profile HC49/US Package. 12MHz is good for use with devices th...

SKU: SF-PRT-08535 | Brand: SparkFun

This 2×5 (10-pin) IDC ribbon cable with 2.54 mm pitch connectors is commonly used for AVR ISP programming and general-purpose communication between boards. The cable is 6 inches (approximately 15 cm) in length. Key F...

SKU: DF-FIT0295 | Brand: DFRobot

An assortment of 35 crystal oscillators covering 7 of the most commonly used frequencies. Keep them on hand for microcontroller projects, prototyping, and circuit experiments — no more hunting for the right crystal wh...

SKU: SF-PRT-08506 | Brand: SparkFun

A 2×5 (10-pin) shrouded box header on standard 0.1" (2.54 mm) pitch. The keyed shroud prevents reversed cable connections, making it ideal for programming headers, data buses, and other multi-pin interfaces. Key Feat...