All Products

SKU: AF-589 | Brand: Adafruit

A value pack of three Adafruit Perma-Proto Quarter-Sized Breadboard PCBs. Each board mirrors the layout of a tiny solderless breadboard (plus power rails) with 5-hole connected pads, four power bus rails, and clear si...

SKU: AF-3244 | Brand: Adafruit

A compact three-layer round robot chassis kit with two DC drive motors, matching wheels, and a caster ball for balance. The high-strength anodised aluminium alloy frame provides a sturdy platform for building your own...

SKU: SF-COM-10349 | Brand: SparkFun

The FQP27P06 is a P-channel enhancement-mode power MOSFET rated for −60V and −27A. With a very low on-resistance of 70 mΩ and a gate threshold compatible with 5V logic, it is well suited for high-side switching contro...

SKU: AF-1831 | Brand: Adafruit

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will...

SKU: AF-1891 | Brand: Adafruit

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (pr...

SKU: AF-641 | Brand: Adafruit

A 3-ply conductive thread made entirely from 316L stainless steel fibre. Thin enough to sew by hand with a medium-eye needle, yet strong and smooth — ideal for wearable electronics, e-textile projects, and sewable cir...

SKU: SF-BOK-12730 | Brand: SparkFun

With more than 60 practical and creative hacks, this book helps you turn Raspberry Pi into the centerpiece of some cool electronics projects. Want to create a controller for a camera or a robot? Set up Linux distribut...

SKU: SF-SEN-10264 | Brand: SparkFun

A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Gl...

SKU: SF-TOL-10242 | Brand: SparkFun

We don’t want to hype this solder TOO much, but this could possibly be the best solder in the world. There, we’ve said it. This is a special blend made specifically for us and we love it. It all started as a quest ...

SKU: DF-DFR0406 | Brand: DFRobot

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two...

SKU: SF-BOB-12700 | Brand: SparkFun

This simple breakout board routes a female USB Type-A connector's VCC, GND, D−, and D+ pins to a standard 0.1″ pitch header. It saves you the hassle of soldering tiny SMD connectors when adding USB host or device conn...

SKU: DF-FIT0481 | Brand: DFRobot

INTRODUCTION A new micro metal gear motor with a difference! This motor comes with a built-in encoder which measures the motor's speed in real time. The average output number of pulses ca...

SKU: DF-FIT0486 | Brand: DFRobot

INTRODUCTION A new micro metal gear motor with a difference! This motor comes with a built-in encoder which measures the motor's speed in real time. The average output number of pulses ca...

SKU: AF-3203 | Brand: Adafruit

The Adafruit Perma-Proto Bonnet Mini Kit is a prototyping daughter board sized for the Raspberry Pi Zero. It plugs directly onto the Pi's 2×20 GPIO header and provides a grid of 0.1″ soldering holes connected in a fam...

SKU: AF-3406 | Brand: Adafruit

The Feather nRF52 Bluefruit LE is an all-in-one Bluetooth Low Energy development board built around the Nordic nRF52832. Unlike earlier Bluefruit Feathers that used a separate helper chip, the nRF52832 runs your appli...

SKU: SF-BOB-10031 | Brand: SparkFun

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping nee...

SKU: AF-732 | Brand: Adafruit

Add another 16 pins to your microcontroller using a MCP23017 port expander. The MCP23017 uses two i2c pins (these can be shared with other i2c devices), and in exchange gives you 16 general purpose pins. You can...

SKU: DF-FIT0491 | Brand: DFRobot

INTRODUCTION   This DC gearmotor has an integrated M4*55mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 150RPM, equivalent to 1.75mm/s. ...

SKU: AF-759 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male head...

SKU: DF-FIT0503 | Brand: DFRobot

INTRODUCTION This is a miniature stepper motor with 100:1 metal reduction gear box for enhanced torque. It has a voltage input range of 5 - 12V DC. This product is suitable for the 3D printers and applications wh...