Actuators

SKU: DF-SER0064 | Brand: DFRobot

##Introduction This is an exceptional water-resistant digital servo with impressive torque. It boasts a torque capacity of 35kg and a controllable angle of 180 degrees. It exhibits superior linear motion and features ...

SKU: AF-6120 | Brand: Adafruit

A 70mm USB-powered cooling fan that delivers reliable airflow for electronics projects. Simply plug into any USB port for immediate cooling — no drivers or setup required. The USB connector can be cut off to wire the...

SKU: AF-6105 | Brand: Adafruit

This compact 3cm USB-powered cooling fan provides instant airflow to prevent electronics from overheating. Simply plug it into any USB port for immediate cooling, or cut off the USB connector to wire it directly to a ...

SKU: AF-6101 | Brand: Adafruit

This 4cm USB-powered cooling fan provides instant airflow to prevent electronics from overheating. Simply plug it into any USB port for immediate cooling, or cut off the USB connector to wire it directly to a 5V power...

SKU: AF-5592 | Brand: Adafruit

This servo is just like our classic Micro Servo but has 3 alligator clip test leads at the end! This makes it perfect for plug-and-play support with any of our boards with alligator-clip-friendly input/output pins, li...

SKU: AF-4699 | Brand: Adafruit

A simple DC-powered air pump for inflatables and air-powered projects. Power it with ~4.5V (5V works fine) and it draws about 500mA, making it easy to run from the same supply as your DC motors or servos. The pump suc...

SKU: PL-2481 | Brand: Pololu

The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. This item includes the basic carrier PCB along with an Omron G5L...

SKU: DF-DFR0173 | Brand: DFRobot

A low power version of the USB-RLY16 module, the USB-RLY16L is powered solely from the USB bus and provides eight volt free contact relay outputs with a current rating of up to 16Amp each. The relays are SPCO (Single ...

SKU: SF-ROB-09347 | Brand: SparkFun

Here, for all your mechatronic needs, is a simple, high quality continuous continuous rotation servo motor. This servo is able to take in 6 volts and deliver 66.7 oz-in. of maximum torque at 70 r/min. A standard 3-p...

SKU: SF-ROB-11965 | Brand: SparkFun

A reliable, high-torque standard-size servo (FS5106B) with dual ball bearings and nylon gears. Delivering up to 83.47 oz-in of torque at 6V with a speed of 0.16 sec/60°, it's a versatile choice for robotics, RC, and m...

SKU: SF-ROB-11884 | Brand: SparkFun

This is the classic Hitec HS-422 servo. This solid consumer grade servo is able to take in 6 volts and deliver 57 oz-in. of maximum torque at 0.16 sec/60°, this is a simple servo for any beginner project!This high qua...

SKU: SF-COM-10924 | Brand: SparkFun

These are massive single pole - double throw (SPDT) sealed relays. This means that when current is applied to the coil it throws a simple changeover switch, terminating the connection from the NC contact to ground and...

SKU: DF-FIT0419 | Brand: DFRobot

INTRODUCTION This is a new micro DC geared motor, using planetary gear mechanism, applicable to the various types of DIY project. Especially the project which has a certain requirements for ...

SKU: SF-ROB-10189 | Brand: SparkFun

Here, for all your mechatronic needs, is a simple, high quality continuous rotation servo motor. This servo is able to take in 6 volts and deliver 30.6 oz-in. of maximum torque at 0.14 sec/60° A standard 3-pin power...

SKU: DF-FIT0045 | Brand: DFRobot

A pan-and-tilt servo assembly for horizontal surface mounting, built with two DFRobot DF05BB ball-bearing servos and aluminium brackets. Ideal for camera gimbals, sensor heads, and small remote-controlled robot platfo...

SKU: DF-DRI0056 | Brand: DFRobot

This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports L...

SKU: DF-SER0057 | Brand: DFRobot

This clutch servo is designed for robots, models and other mechanisms where the servo may be pushed, stalled or forced out of position during use. Its clutch function helps protect the servo by allowing it to reset an...

SKU: SF-ROB-31141 | Brand: SparkFun

Add motion and feedback to small robotics builds with this single DC gearmotor and integrated Hall effect speed encoder. Instead of simply driving a motor open-loop, your microcontroller can count encoder pulses to tr...

SKU: AF-1404 | Brand: Adafruit

This standard-size hobby servo adds a handy fourth white wire that brings out the internal potentiometer wiper. Connect it to an analogue input on a board such as an Arduino to read the servo’s position as a voltage w...

SKU: WS-31284 | Brand: Waveshare

Built around the ESP32-S3 dual-core processor, this industrial relay module brings local control, networking and edge automation into one DIN-rail friendly unit. It combines 8 relay outputs, 8 digital inputs, isolated...