All Products

SKU: PL-957

This ball caster was originally released as a replacement part for the 3pi robot, but the 1/2″ ball can also be used a replacement part for the newer 3pi+ robot, which has the housing for the ball built directly into the chassis. This ball caster can also be used as a general-purpose ball caster...

SKU: AF-4767 · MPN: 4767

Here's a handy power cable for the RGB LED Matrix Panels we carry.Easily plug into the back of your RGB matrix and insert or screw the power and ground cables onto either the Matrix Portal or the Matrix Bonnet, or whichever microcontroller-and-add-on you're using for your RGB Matrix project.Works...

SKU: AF-4728 · MPN: 4728

A replacement CSI/DSI flex connector for the Raspberry Pi. If the camera or display connector on your Pi has been damaged — snapped arms, broken latch — this part lets you rework it rather than replacing the entire board. The same connector is used for both the Camera (CSI) and Display (DSI) por...

SKU: PL-3434

This is a full set of replacement gears for the Power HD High-Torque Servo 1501MG.

SKU: AF-2476 · MPN: 2476

Replacement silicone tubes for the Professional Silicone-Tip Solder Sucker. Cut to your desired length as needed — the elastic, heat-resistant silicone withstands temperatures up to 350°C, letting you get close to your soldering iron and suck up molten solder with little to no residue. Key Featu...

SKU: AF-3428 · MPN: 3428

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually the battery runs down, and goes below 3.3V, so the voltage to the ESP8266...

SKU: SF-COM-08357

This is a handy little device that can save your system from smoking. A resettable fuse (also known as a PTC) is a resistor that has very unique properties.  For this model, if your circuit tries to draw more than 250mA of current (if you have a bad short for instance) the PTC would ‘trip’ (...

SKU: LB-00017

Reship your order via Australia Post Express Post.

SKU: LB-00073

Reship My Order

SKU: LB-00021

Reshipping an order via Regular Parcel Post

SKU: AF-1662 · MPN: 1662

Streeeeetch your resistive touch-screen's reach with a 20cm extension cord. This is a great accessory for our resistive touch screen controller breakouts. Plug your 4-pin 1mm pitch FPC into the socket end and the other end into your controller board. Pretty nice! The socket connector on the cable...

SKU: AF-1676 · MPN: 1676

If you already have a 7" TFT that is about 165mm x 105mm in size (with a visible area equal to or smaller than 152mm x 91mm), you can put this glass resistive overlay over it to add a resistive touch screen. To use, first remove the protective plastic wrap from both sides. Attach to your touc...

SKU: AF-1580 · MPN: 1580

Getting touchy performance with your screen's touch screen? Resistive touch screens are incredibly popular as overlays to TFT and LCD displays. If you want to connect one to a computer you need something to handle the analog to digital conversion. Most converters we've found are not very easy ...

SKU: SF-PRT-14493

These are your run-of-the-mill ¼ Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and other prototyping applications, these 100 ohm resistors make excellent pull-ups, pull-downs and current limiters. These thick-lead versions of the resistors fit snugly into a breadboard with...

SKU: SF-PRT-14491

A pack of 20 through-hole 10 kΩ resistors with thick leads designed for a snug fit in solderless breadboards. These are standard ¼ W, ±5% tolerance PTH resistors — ideal for pull-ups, pull-downs, current limiting, and general prototyping. Specifications Resistance – 10 kΩ Tolerance – ±5% Pow...

SKU: SF-COM-08374

1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 10K resistors make excellent pull-ups, pull-downs, and current limiters. Need more than one? Checkout our bag of resistors. If you need a bunch of these, you can get good bulk discounts on Digike...

SKU: SF-COM-11508

1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 10K resistors make excellent pull-ups, pull-downs, and current limiters. We’ve opted for a new and more breadboard-friendly lead thickness (they’re a bit thicker than our last ones). These resistors...

SKU: SF-COM-11853

1.0M Ohm, ¼th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards.We’ve opted for a new and more breadboard-friendly lead thickness (they’re a bit thicker than our last ones). Note: Sold as singles. But check below for multi-packs. Documents: Breadboard Lectu...

SKU: SF-PRT-14492

These are your run-of-the-mill ¼ Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and other prototyping applications, these 1K ohm resistors make excellent pull-ups, pull-downs and current limiters. These thick-lead versions of the resistors fit snugly into a breadboard with ve...

SKU: SF-PRT-14494

These are your run-of-the-mill ¼ Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and other prototyping applications, these 1M ohm resistors make excellent pull-ups, pull-downs and current limiters. These thick-lead versions of the resistors fit snugly into a breadboard with ver...