All Products

SKU: AF-603 · MPN: 603

This 316L stainless steel conductive yarn sits between a thick thread and a thin yarn in weight. Its high conductivity and soft, flexible texture make it particularly well-suited for making touchscreen-compatible gloves and other projects that require capacitive touch conductivity. Sew a few sti...

SKU: AF-178 · MPN: 178

A 100 mm linear soft potentiometer (ribbon sensor) manufactured by Spectra Symbol. This pressure-sensitive ribbon controller features an adhesive backing for easy mounting and provides a variable resistance output based on the position of touch along its length. Key Features 100 mm Active Leng...

SKU: SF-SEN-09674

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being appli...

SKU: AF-1088 · MPN: 1088

This conductive fiber is super interesting! It's great for felting and could also be spun into yarn if that's your thing. We tested many different fiber thicknesses for needle felting and found that this one (20um fiber thickness) is the most pleasurable to work with. Use about 0.2g of the stu...

SKU: DF-FIT0788-V2 · MPN: FIT0788-V2

##Introduction This is an Aluminum case and heat sink kit built specifically for the Raspberry Pi CM4 IoT Router Carrier Board Mini. The kit allows the Raspberry Pi CM4 IoT Router Carrier Board Mini to be safely housed within a power distribution box, eliminating concerns about short circuits on ...

SKU: SF-SEN-12909

This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid. Depending on how you...

SKU: SF-SEN-09376

This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be lar...

SKU: AF-1656 · MPN: 1656

3M Z-Axis Conductive Tape (9703) bonds two conductive surfaces together while allowing current to flow through the thickness of the tape — but not along its length or width. This anisotropic conductivity is achieved by conductive particles embedded in the adhesive approximately every 0.1mm, makin...

SKU: DF-SEN0337

TOF Sense is a TOF-based (Time of Flight) laser ranging sensor that offers 1cm-5m detection range, 1mm resolution, ± 1.5cm error, and 10Hz data update frequency. The sensor supports 15 ° ~ 27 ° adjustable FOV, UART and CAN communication (selected by setting). Besides, it allows users to actively ...

SKU: SF-SEN-09375

This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be ...

SKU: PI-COM-B005

580 resistors (29 values, 20 pieces of each) go into this great starter pack (or refill!) with a wide range of useful values. The kit contains 20 each of:10Ω22Ω47Ω68Ω100Ω120Ω150Ω180Ω220Ω270Ω330Ω470Ω560Ω680Ω1kΩ1.2kΩ1.5kΩ1.8kΩ2.2kΩ2.7kΩ3.3kΩ4.7kΩ5.6kΩ6.8kΩ8.2kΩ10kΩ22kΩ47kΩ100kΩ Rated for&nb...

SKU: SF-DEV-11791

This is about 360 yards of conductive thread spun from stainless steel fiber and wound on a spool. You can use it as a creative way to connect various electronics onto clothing projects. This large spool is a great way to get into wearable electronics without a large upfront cost and a large e...

SKU: AF-166 · MPN: 166

The Interlink 402 is a round force-sensitive resistor (FSR) with a 12.7 mm (0.5″) sensing area. It changes resistance based on applied pressure — the harder you press, the lower the resistance — making it a simple, low-cost way to detect physical pressure, squeezing, and weight in your projects. ...

SKU: SF-DEV-10867

This is 30 feet of conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the upfront cost of buying an entire spool of thread. 30 feet of thread...

SKU: AF-5672

The ESP32-C6-DevKitC-1-N8 is an entry-level development board equipped with ESP32-C6-WROOM-1,  a general-purpose Wi-Fi + Bluetooth LE RISC-V MCU module that integrates complete Wi-Fi and Bluetooth LE functions. This board integrates complete Wi-Fi, Bluetooth LE, Zigbee, and Thread functions....

SKU: EF-EF04087

Octopus BME280 Pressure Sensor is an electric brick, which has integrated temperature sensor, air pressure sensor and humidity sensor onboard. We can use it to measure humidity, temperature and air pressure, or even to calculate the altitude according to the measured air pressure. Features Low...

SKU: AF-4685 · MPN: 4685

A comprehensive 420-piece set of black nylon M3 screws, nuts, and hex standoffs in a reusable storage container. Nylon fasteners are non-conductive, making them ideal for mounting PCBs and breakout boards without interfering with antennas or magnetometers. They can also be easily filed down to cu...

SKU: AF-1075 · MPN: 1075

A force-sensitive resistor (FSR) that changes its resistance based on how much pressure is applied. This Interlink 406 model features a 38 mm square sensing region, making it useful for detecting physical pressure, squeezing, and weight in your projects. FSRs are simple and low cost, but not pre...

SKU: AF-1209 · MPN: 1209

Keep your circuit boards spotless with this ESD-safe cleaning brush. Its stiff bristles effectively remove flux residue, rosin, and solder debris without risking damage to sensitive components from static discharge. For best results, apply a small amount of isopropyl alcohol to the PCB and scrub...

SKU: ED-MMBK-CC · MPN: MMBK-CC

The materials you'd otherwise spend a weekend sourcingConductive thread, conductive fabric and correctly graded graphite pencils are the three things that stall a Makey Makey art project. This booster kit packages them alongside ordinary craft supplies so a soft-circuit or drawn-circuit lesson ca...