All Products
AI Overview
Here are the main Pololu options that match this search, grouped by common use:
Motor drivers (Raspberry Pi / Arduino)
- For Raspberry Pi and higher-current brushed DC motors: Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi (Assembled) — up to 14A continuous/channel, up to 24V ($113.30).
- For Raspberry Pi and smaller motors: Dual MAX14870 Motor Driver for Raspberry Pi — 4.5–36V, up to 1.7A continuous/channel ($31.50).
- For Arduino motor control in shield form factor: Pololu Dual G2 High-Power Motor Driver 18v18 Shield for Arduino — dual high-power H-bridges for brushed DC motors ($94.50).
Power (step-down regulators)
- For regulated 5V rails from higher-voltage batteries/supplies: Pololu 5V, 2.5A Step-Down Voltage Regulator D24V22F5 — up to 36V input, 2.5A ($45.00).
- For regulated 12V output: Pololu 12V, 2.2A Step-Down Voltage Regulator D24V22F12 — up to 36V input, 2.2A ($27.95).
Motors & motion hardware
- Geared motor with feedback: 34:1 Metal Gearmotor 25Dx52L mm HP 12V with 48 CPR Encoder — 12V, 34:1 gearbox, 48 CPR quadrature encoder ($74.15).
- Small robot wheels: Pololu Wheel 40x7mm Pair - Red — 40mm diameter, press-fit for 3mm D-shafts ($9.10).
- Motor mounting: Pololu Micro Metal Gearmotor Bracket Extended Pair — mounting bracket set for Pololu micro metal gearmotors ($8.30).
- Caster support: Pololu Ball Caster with 1" Plastic Ball and Ball Bearings — ball caster for small robot chassis ($19.50).
- Shaft/wheel coupling hubs: Pololu Universal Aluminum Mounting Hub for 5mm Shaft, #4-40 Holes (2-Pack) — 5mm shaft hubs ($19.60); Pololu Universal Aluminum Mounting Hub for 8mm Shaft, M3 Holes (2-Pack) — 8mm shaft hubs ($14.25).
Sensors & switching
- Gas sensor carrier: Pololu Carrier for MQ Gas Sensors (Bare PCB Only) — breakout/carrier for MQ-series gas sensors ($2.25).
- Relay switching modules: Pololu Basic SPDT Relay Carrier with 5VDC Relay (Partial Kit) ($4.00), Pololu Basic SPDT Relay Carrier with 12VDC Relay (Assembled) ($9.95), and Pololu Basic 2-Channel SPDT Relay Carrier with 5VDC Relays (Assembled) — 2-channel SPDT ($17.05).
What type of Pololu part are you looking for?
Collections
Showing 81-100 of 100 products
A4988 Stepper Motor Driver Carrier, Black Edition
The Black Edition of the A4988 stepper motor driver carrier features a four-layer PCB for better thermal performance, allowing the A4988 to deliver approximately 20% more current than the standard two-layer (green) version. It is a drop-in replacement for the original carrier in most applications...
Sharp GP2Y0D805Z0F Digital Distance Sensor 5cm
This small digital distance sensor detects objects between 0.5 cm and 5 cm (0.2″ and 2″) away. With its quick response time, small size, low current draw, and short minimum sensing distance, this sensor is a good choice for non-contact object detection, and its short minimum detection d...
Power HD Micro Servo HD-1600A
The HD-1600A analog servo from Power HD is a great general-purpose micro servo at a great price. Servo horns and associated hardware are included.Key specs at 6 V: 0.10 sec/60°, 18 oz-in (1.3 kg-cm), 6.0 g.
Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm
This small digital distance sensor detects objects between 2 cm and 10 cm (0.8″ and 4″) away. With its quick response time, small size, and low current draw, this sensor is a good choice for non-contact object detection.
3-AA Battery Holder, Enclosed with Switch
An enclosed battery holder for three AA cells with a built-in on/off switch. The snap-on lid slides over the batteries to fully enclose them, keeping the cells secure during use. Provides approximately 4.5 V with three alkaline AA batteries (3 × 1.5 V) or 3.6 V with three NiMH rechargeable cells...
6-AA Battery Holder
A compact enclosed battery holder for six AA batteries, providing approximately 9V (alkaline) or 7.2V (NiMH rechargeable) from a series configuration. Features bare wire leads for flexible integration into your project. Key Features 6-Cell Capacity – Holds six AA batteries in series Enclosed ...
8-AA Battery Holder, Back-to-Back
A battery holder for eight AA cells, arranged as two back-to-back four-cell holders. Provides up to 12V (with alkaline cells) in a compact, stackable form factor. Specifications Cell Type – AA Capacity – 8 cells Configuration – Two 4-cell holders, back-to-back Output – Up to 12V (series, al...
Ceramic Capacitor 3-Pack 0.1uF 100V
These 0.1 μF 100 V ceramic capacitors have many uses, including noise suppression on motors.
Tamiya Plug with 10cm Leads, Male
A male Tamiya-style high-current connector with two pre-crimped 10cm 14-AWG silicone-insulated leads. This keyed connector is commonly used with 7.2V RC battery packs and features a latch to prevent accidental disconnection. The leads extend 9cm past the housing with stripped, tinned terminations...
Vibration Motor 11.6x4.6x4.8mm
This tiny DC motor has a shaft with an offset mass that vibrates when it rotates. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback. The motor has 1.5″ leads and is encased in a removable rubber sleeve that gives it flat surfaces for m...
Stepper Motor: Bipolar, 200 Steps/Rev, 42x38mm, 2.8V, 1.7 A/Phase
A NEMA 17 hybrid bipolar stepper motor with a 1.8° step angle (200 steps per revolution). Each phase draws 1.7 A at 2.8 V, delivering a holding torque of 3.7 kg·cm. Four colour-coded wires with bare leads connect to two coils: black/green for one coil, red/blue for the other. Best driven with a ...
Snap-Action Switch with 16.7mm Lever: 3-Pin, SPDT, 5A
This single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch or tactile bump sensor for your robot. The switch body dimension is 20.0 x 6.4 x 10.2 mm, and the lever arm is 16.7 mm long.
Snap-Action Switch with 50mm Lever: 3-Pin, SPDT, 5A
This single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch, but the long lever arm makes it especially useful as a tactile bump sensor for your robot (e.g whiskers or antennae). The switch body dimension is 20.0 x 6.4 x 10.2 mm, ...
Rocker Switch: 3-Pin, SPDT, 10A
This single-pole, double-throw (SPDT) rocker switch makes a great on/off power switch. It is rated for 10 A at 125 VAC and 6 A at 250 VAC.
170-Point Breadboard (White)
A compact 170-point solderless breadboard in classic white, perfect for small circuits and prototyping with DIP ICs. The 17-row layout accommodates up to two 14- or 16-pin DIP packages, making it ideal for quick test circuits and portable projects. Interlocking tabs on the sides allow multiple b...
Screw Terminal Block: 3-Pin, 5 mm Pitch, Side Entry (4-Pack)
These side-entry screw terminal blocks have a pitch of 5 mm (0.197″). Each block has three terminals for the stripped ends of 22 – 14 AWG wires, and units can slide together to make longer strips. They are rated for 250 V, 16 A (UL) and ship in packs of four.
Screw Terminal Block: 2-Pin, 5 mm Pitch, Side Entry (4-Pack)
A pack of four 2-pin screw terminal blocks with 5 mm pitch and side-entry wire orientation. Simply tighten or loosen the screws to connect or release wires — no soldering needed for the wire connection itself. Each block features a ridge on one side and a slot on the other, allowing multiple blo...
DC Barrel Jack to 2-Pin Terminal Block Adapter
This connector adapts a 5.5 × 2.1 mm DC barrel jack to a pair of screw terminals spaced approximately 5 mm (0.2″) apart. The terminals are labeled positive and negative, with the positive terminal connected to the center pin.
Vishay TSSP58P38 IR Detector Module, 38kHz, Automatic Gain (3-Pack)
The Vishay TSSP58P38 is a unique modulated IR receiver that is designed for IR brightness detection instead of data communication for remote control. This sensor can be used with a 38 kHz modulated IR emitter and the appropriate algorithms to form a distance sensor with a range of up to a f...
QTR-1A Reflectance Sensor (2-Pack)
The QTR-1A reflectance sensor carries a single infrared LED and phototransistor pair in an inexpensive, tiny 0.5" x 0.3" module that can be mounted almost anywhere and is great for edge detection and line following. The reflectance measurement is output as an analog voltage. This sens...
