All Products
Showing 1-20 of 30 products
Micro:bit Robit Smart Car（without micro:bit board）
*note colour may varyLearning about electronics and programming can be simple and fun! The Robit Smart Car is an ideal starting point for those new to electronics and programming. This gentle introduction to robotics uses the beginner-friendly BBC Micro:bit, a tiny programmable computer used...
Electronic brick - Protoshield kit
This is a Protoshield kit with the same connector as Electronic Brick, you can solder something onto this and use it as a regular Electronic Brick. You will also need this cable to connect it to Sensor shield. http://www.seeedstudio.com/depot/electronic-brick-fully-buckled-4-...
Octopus Non-invasive AC current sensor TA12-100 Brick
The Octopus TA12-100 is a non-invasive AC current sensor brick from ElecFreaks. It uses a current transformer to measure AC current flowing through a wire without needing to cut or splice the circuit — simply clamp it around the conductor. The sensor outputs an analogue voltage proportional to th...
Ultra Sonic range measurement module
This is a non-contact distance measurement module, which is also compatible with electronic brick. It’s designed for easy modular project usage with industrial performance. Features Detecting range: 3cm-4m Best in 30 degree angle Electronic brick compatible interface ...
Raspberry Pi Arduino Shield Add-on
Overview Compared to Arduino, it's hard to find the shields and electronic brick customized for Raspberry Pi. This RPI Arduino Shield Add-on has extended 32pin connector of RPI to Arduino pins, which will facilitate connections to all kinds of arduino shields. Meanwhile, two groups of elect...
OCTOPUS 1-Channel Relay
OCTOPUS 1-Channel Relay is a single relay electronic brick: Note: Module 5V power supply: Never use power supply more than 5V, which may cause damage to the module. Features: Relay Power Supply Voltage:<V Relay drive level: With opto-isolation circuit, can completely isolate the relay controll...
Octopus PM2.5 module
The Octopus PM2.5 module from ElecFreaks is a laser-based particulate matter sensor built around the ZH03B dust sensor. It measures PM2.5 concentration in the air with high consistency and real-time response, capable of detecting particles as small as 0.3 µm in diameter. Part of the Octopus elec...
Octopus MG811 CO2 Gas Sensor
Octopus MG811 CO2 Gas Sensor is a CO2 electronic brick in our OCTOPUS series, the basic design for the outlook, PCB fixing holes and connections are the same with them.The higher the CO2 concentration is, the lower the output voltage would be. The users can read the CO2 value easily after checkin...
Octopus Non-invasive AC current sensor TA17-03 Brick
Octopus Non-invasive AC current sensor (TA17-03) Brick is Electronic building blocks, a transformer, an ammeter, a current sensor module, compatible with all kinds of Arduino electronic building blocks / sensor shield. 3P electronic building blocks interface, input 5V - GND, S pin for output a...
Octopus Push Lock E-Switch Brick OBPLock
Octopus Electronic Bricks, you can use them build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connection a...
Octopus Motor Brick
OCTOPUS Motor Brick is a type of simple electronic building blocks of the fan motor drive module, it can be used as simple Arduino teaching demo, convenient for Arduino beginners to learn. Features: Power supply: 5V N-MOS IRLML2502TRPBF with high current driving capability low-po...
Octopus Button Switch Brick OBButton
The Octopus Button Switch Brick is a simple, plug-and-play pushbutton module from the ElecFreaks Octopus Electronic Bricks series. It features a large button with a transparent cap — you can insert a custom label underneath for easy identification in your projects. Designed for breadboard-free c...
Octopus 5mm LED Brick - Green
A green 5 mm LED module from the Octopus Electronic Bricks range. It connects to Arduino or micro:bit via a 3-pin sensor cable for breadboard-free, plug-and-play wiring. Control it with a digital pin (LOW = on, HIGH = off) or use PWM to adjust brightness. Key Features 5 mm Green LED – Standard...
Octopus 5mm LED Brick OBLED - Blue
Octopus Electronic Bricks, you can use them build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connection a...
Octopus Passive buzzer Brick OBPB01
The Octopus Passive Buzzer Brick is a plug-and-play buzzer module from the Elecfreaks Octopus series. Unlike an active buzzer, the passive design lets you control both tone and volume via PWM, making it ideal for generating melodies, alarms, and sound effects. Part of the Octopus Electronic Bric...
Octopus Linear Slider Potentiometer Brick
A linear sliding potentiometer module from the ElecFreaks Octopus series. Provides an analogue voltage output proportional to the slider position, making it useful as a variable input for controlling volume, brightness, speed, or any other parameter in your project. Features a standard 3-pin con...
Octopus Analog Rotation Brick OBARot
Octopus Electronic Bricks, you can use them to build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connectio...
Octopus Vibration Detection Brick OBVD01
Octopus Electronic Bricks, you can use them to build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connectio...
Octopus Analog Photocell Brick OBPhotocell
The Octopus Analog Photocell Brick is a light-dependent resistor (LDR) module from the ElecFreaks Octopus Electronic Bricks series. It uses a cadmium-sulfide (CdS) photocell that changes resistance based on ambient light levels — the brighter the light, the lower the resistance. With its 3-pin co...
Octopus 5mm LED Brick OBLED - Red
Octopus Electronic Bricks, you can use them build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connection a...
