All Products
Showing 1-20 of 48 products · 12 unavailable products hidden
Waterproof 3xAA Battery Holder with On/Off Switch
Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...
3 x AA Battery Holder with On/Off Switch, JST, and Belt Clip
A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...
3-AA Battery Holder, Enclosed with Switch
An enclosed battery holder for three AA cells with a built-in on/off switch. The snap-on lid slides over the batteries to fully enclose them, keeping the cells secure during use. Provides approximately 4.5 V with three alkaline AA batteries (3 × 1.5 V) or 3.6 V with three NiMH rechargeable cells...
3xAA Battery Holder
This enclosed battery holder takes 3× AA batteries in series, providing approximately 4.5V from alkaline cells or 3.6V from NiMH/NiCd rechargeables. It features a built-in on/off switch and a sliding, removable cover for easy battery access. Compatible with both non-rechargeable alkaline and rec...
Battery Holder 3xAA with Cover and Switch - JST Connector
This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The 6" (~150mm) cable has been terminated with a JST connector. Note: Please keep in...
Battery Holder 3xAA with Cover and Switch
This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.The leads are about 150mm...
8 x AA battery holder with 5.5mm/2.1mm Plug and On/Off Switch
This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. Use alkaline AAs for approximately 12V at 3000–4000 mAh, or rechargeable NiMH cel...
4 x AA Battery Holder with 2.1mm Plug and On/Off Switch
A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4....
Kitronik ZIP Halo HD for micro:bit
The Kitronik ZIP Halo HD for micro:bit is the ultimate micro:bit interface. 60 full-colour ZIP LEDs, Pins 1 & 2 broken out, MEMs mic, Piezo sounder, RTC & more!The Kitronik Halo HD board for the BBC micro:bit incorporates 60 individually addressable full colour ZIP LEDs. It also breaks out P1 and...
Adafruit Proto Tripler PiCowbell for Pico and PicoW
·
The Adafruit Proto Tripler PiCowbell gives your Raspberry Pi Pico or Pico W three side-by-side socket slots — plug in your Pico and up to two PiCowbell accessories with no soldering or stacking headers required. It also includes LiPo battery charging, a power switch, reset button, STEMMA QT conne...
12mm Coin Cell Breakout w/ On-Off Switch
A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) module. The board breaks out four pins: two ground pins, one switched power pin...
Waterproof 2xAA Battery Holder with On/Off Switch
Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...
2 x AA Battery Holder with On/Off Switch JST PH Connector
A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...
Adafruit LED Glasses Starter Kit
The Adafruit LED Glasses Starter Kit includes everything you need to build a complete pair of programmable LED glasses. Pair the 116-LED front panel with the Bluetooth-enabled nRF52840 driver board, snap them onto the included fashion frames, and you're ready to create dazzling wearable light dis...
MicroUSB Battery Holder (3xAA)
This battery holder takes three AA cells and provides a simple way to power compatible Arduino-style boards via a Micro USB connection.Use it with NiMH or NiCd rechargeable cells for a 3.6V battery pack, or with alkaline cells for a 4.5V battery pack. The holder is made from plastic and includes ...
Kitronik Air Quality and Environmental Board for micro:bit
The Kitronik Air Quality Board provides a complete air monitoring and reporting solution for the BBC micro:bit. The wealth of onboard sensors and connection points allow you to collect extensive air quality data that can be stored in onboard memory and displayed on the OLED screen or transferred ...
4x AA Battery Holder (with Power Switch, DC2.1 Jack, and Cover)
A compact 4×AA battery holder with a built-in on/off power switch, DC2.1 barrel jack output, and a protective cover. Ideal for powering Arduino, Raspberry Pi, and other microcontroller projects with a portable 6V supply. The holder accepts four standard AA batteries (1.2V rechargeable or 1.5V al...
FLORA Budget Pack
Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3x...
Kitronik ARCADE Max for Makecode Arcade
Develop your coding skills with the ARCADE Max, a fully featured programmable gamepad for use with the MakeCode Arcade block editor, featuring a large 2.4" screen and familiar design shape.The Kitronik ARCADE Max for Makecode Arcade is an all-in-one handheld gaming platform, that can help you lea...
Battery Holder 4xAA with Cover and Switch
This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.The leads are about 150mm...
