All Products

SKU: AF-5743

The Adafruit Mini I2C Gamepad is a compact controller breakout with a 2-axis thumb joystick and 6 momentary buttons (4 large, 2 small), all communicating over I2C via the seesaw co-processor. It doesn't use any of your GPIO or analogue pins — just connect via STEMMA QT / Qwiic and start reading i...

SKU: AF-5753

Bring your classic PC joystick back to life. This adapter board takes any legacy DE-15 game port joystick and converts its analogue X/Y axes and two buttons to I2C via an onboard ATtiny816 running the Adafruit seesaw firmware. No analogue inputs needed on your microcontroller — just plug in a STE...

SKU: AF-3632

The Adafruit Joy FeatherWing adds a 2-axis joystick and five buttons to any Feather board over I2C — no GPIO or analogue pins consumed. Using Adafruit's Seesaw technology, an onboard helper microcontroller reads the joystick and button inputs and presents them as a clean I2C interface, compatible...

SKU: AF-4836

Turn a Wii Nunchuck into a versatile I2C controller for your next project with the Adafruit Wii Nunchuck Breakout Adapter. It fits snugly into the Wii connector and handles level shifting and power regulation, so you can use the controller with any 3.3V or 5V microcontroller. The Wii Nunchuck co...

SKU: SF-SEN-22397

The SparkFun BMI270 6DoF IMU Breakout is a Qwiic-enabled board featuring the ultra-low-power BMI270 inertial measurement unit from Bosch. It combines a 16-bit tri-axial accelerometer and 16-bit tri-axial gyroscope with intelligent on-chip motion detection features optimised for wearable applicati...

SKU: SF-DEV-17156

An extended Qwiic shield that adds four Qwiic connectors to Teensy 4.1, Teensy 3.6, and Teensy 3.5 boards. Connects the I²C bus (GND, 3.3 V, SDA, SCL) to two horizontal and two vertical Qwiic ports for easy daisy-chaining of I²C sensors and actuators. Includes a PROG button that mirrors the Teen...

SKU: SF-KIT-15367

The SparkFun Qwiic Kit for Raspberry Pi provides everything you need to start using I2C sensors and displays with your Raspberry Pi via the Qwiic connector system. The kit includes a Qwiic HAT that adds four Qwiic connectors to your Pi's GPIO header, along with three sensor/display breakouts and ...

SKU: AF-4506

The Adafruit 1.3" Colour TFT Bonnet for Raspberry Pi combines a 240×240 IPS TFT display with a 5-way joystick and two pushbuttons on a single plug-and-play bonnet. The display is driven by the ST7789 controller over SPI, delivering vibrant 16-bit colour with wide viewing angles. A Qwiic/STEMMA Q...

SKU: SF-DEV-17047

The SparkFun Qwiic GPIO adds eight additional digital I/O pins to your project via I2C, based on the TCA9534 I/O Expander from Texas Instruments. Read and write pins just like standard Arduino digital pins using the included library — functions mirror familiar pinMode and digitalWrite calls. All...

SKU: AF-802

The Adafruit 1.8" Colour TFT Shield is a plug-and-play display solution for Arduino, combining a bright 128×160 pixel TFT screen with a microSD card slot, 5-way joystick navigation switch, and three tactile buttons. This R3-format shield works with any Arduino or Metro board including the Metro M...

SKU: SF-GPS-23288 · MPN: GPS-23288

Bring high-precision GNSS positioning to your project with the u-blox NEO-F9P engine and dual-band L1/L5 reception. L5 signals sit in the protected ARNS band, helping reduce RF interference and improve reliability in challenging environments such as dense city streets.The breakout provides five s...

SKU: SF-GPS-15193

The SparkFun ZOE-M8Q GPS Breakout is a miniaturised, high-accuracy GNSS receiver board with Qwiic (I2C) connectivity. The u-blox ZOE-M8Q is a 72-channel receiver that tracks GPS, GLONASS, BeiDou, and Galileo constellations simultaneously for faster lock times and improved precision. An onboard r...

SKU: AF-3531

The Adafruit 128×64 OLED Bonnet is a compact display add-on for Raspberry Pi, featuring a 1.3" diagonal monochrome OLED screen with a 5-way joystick and two pushbuttons. The high-contrast white OLED pixels are individually lit with no backlight required, delivering crisp, readable text and graphi...

SKU: SF-GPS-15210

The SparkFun SAM-M8Q GPS Breakout features a u-blox SAM-M8Q 72-channel GNSS receiver with a built-in chip antenna. It supports GPS, GLONASS, Galileo, and BeiDou constellations simultaneously, providing improved positional accuracy and faster satellite lock times. The board communicates over I2C ...

SKU: SF-PRT-28203 · MPN: PRT-28203

  The SparkFun Qwiic 5V Boost simplifies interfacing 5V I2C devices with the 3.3V Qwiic ecosystem. It takes the 3.3V I2C signals and power from its Qwiic connectors and boosts them to 5V, available on the PTH pins. This is perfect for powering peripherals like RGB LEDs or DC fans commonl...

SKU: SF-LCD-22495 · MPN: LCD-22495

A compact monochrome OLED breakout board featuring a 64×48 pixel blue-on-black display (0.66" diagonal). Equipped with two Qwiic connectors for solderless I²C connection, plus 0.1"-spaced header pins for breadboard use. The board includes I²C pull-up and address jumpers on the back for flexible c...

SKU: SF-BOB-31206 · MPN: BOB-31206

Generate a real analogue output from your microcontroller instead of relying on PWM. This MCP4725 breakout is a 12-bit Digital-to-Analogue Converter (DAC) that outputs precise voltage levels over an I2C/Qwiic connection.It is useful for projects that need smoother control signals, such as sound g...

SKU: SF-BOB-18012

Qwiic is a very efficient way to quickly prototype an idea but not all Qwiic-enabled devices have two ports. The SparkFun Qwiic MultiPort adds additional ports to boards that have only one Qwiic port on the I2C bus. Once added, you can use it as a hub to add as many I2C devices to the bus as you ...

SKU: AF-4862

The Adafruit CYBERDECK Bonnet is a GPIO extender for the Raspberry Pi 400 that lets you plug any Pi bonnet, mini-HAT, or pHAT into the back of the Pi 400 at an angled position. It duplicates every GPIO pin from input to output, so your add-on boards work without any pin limitations. In addition ...

SKU: SF-DEV-15945

The SparkFun Qwiic pHAT V2.0 for Raspberry Pi provides you with the quickest and easiest way to enter into SparkFun’s Qwiic ecosystem while still using that Raspberry Pi that you’ve come to know and love. The Qwiic pHAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an ...