All Products

SKU: LB-KEY-SCREW

These handy little screwdrivers can be used with our E-Textile boards to add and remove the M1.4 screws to access the coin cell battery.The screwdriver comes on a handy keyring so you can carry it round.These are also great for doing glasses repair and access to phones.

SKU: LB-13-PHILLIPS

 Precision Magnetic Screwdriver 1.3 Phillips.  These handy little screwdrivers can be used with our E-Textile boards to add and remove the M1.4 screws to access the coin cell battery.These are also great for doing glasses repair and access to phones.

SKU: DF-FIT0746 · MPN: FIT0746

This smooth stainless steel fibre sewing thread is conductive, making it handy for e-textiles, wearable electronics and other small-current projects. It has a resistance of about 9Ω per metre and comes as a 7 metre roll.The thread can be sewn into fabric for projects such as touchscreen gloves, a...

SKU: LB-LS3938

This terminal block breakout module comes fully assembled and soldered, ready for use with Raspberry Pi boards.It is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, and Pi Zero W.The module features 2.54 mm (0.1″) pitch terminal blocks su...

SKU: AF-4807

An acrylic faceplate and hardware kit for the Adafruit MagTag. The kit includes two front plate options — a red arrow and a white cloud — plus a back plate and all the nylon mounting hardware needed for assembly. Takes just a few minutes with a Phillips screwdriver. Key Features Two Faceplate ...

SKU: AF-1250

Upgrade your Hakko with a new tip, you'll get better & faster solder joints and the whole process will be much more enjoyable. This tip fits the FX-888 analog and digital irons, and they're fast to swap, takes only 30 seconds to change out. All the tips are good for either lead or lead free (simp...

SKU: AF-1126

Tin-plated brass sewable snaps in a compact 5 mm diameter, ideal for wearable electronics. Solder one side to a PCB pad and sew the other to your project with conductive thread for a detachable electrical connection. Each card contains 24 complete snap pairs (socket and stud). Key Features 5 m...

SKU: LB-EAGLED-MOMENTARY

A pack of 10 low-profile momentary push buttons designed for e-textile and wearable electronics projects. Each button features large sewing holes and flat connection pads with no sharp edges, making them comfortable to wear and easy to sew onto fabric with conductive thread. The button closes th...

SKU: DF-FIT0577

This DC gearmotor are now in the status of Pre-order and will ship in the end of Jun. This DC gearmotor has an integrated M3*20mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 98RPM, equivalent to 1.1mm/s. The brass facepla...

SKU: LB-JSTBOARD

This E-textiles board is a breakout for a JST, so you can sew it onto a garment or use it in Paper Circuits! The JST breakout board can be easily sewn through the large holes. For paper circuits, simply apply copper tape on top of it.A wearable lithium polymer battery or wearable lipo also kno...

SKU: M5-K009-F

A wearable watch kit designed for the M5Stack Core series. This kit transforms an M5Core development board into a wrist-worn smart device, combining the full capabilities of the M5Core with a comfortable strap and integrated 700 mAh lithium battery for extended portable use. Key Features 700 m...

SKU: SF-TOL-10405

This sewing needle set is designed for e-textile projects, with eye sizes large enough to easily thread conductive thread. The set includes both large and small needles to suit different stitching needs — from thick fabric and felt to finer materials. Key Features E-Textile Ready – Eyes sized ...

SKU: LB-ETEXTILELED-YG

A single yellow-green LED module designed for e-textiles projects. Each unit features sewable tabs so it can be stitched directly into fabric using conductive thread. The thicker PCB design makes it more durable than standard sewable LEDs. Compatible with a range of e-textiles input, output, pow...

SKU: DF-FIT0743 · MPN: FIT0743

This smooth stainless steel fibre thread is made for sewing conductivity into fabric and wearable projects. It offers low resistance, good thermal conductivity, a high melting point, and high-temperature resistance.Each roll includes 25 metres of conductive sewing thread with a 0.3mm diameter and...

SKU: SF-GPS-17722 · MPN: GPS-17722

Built around the u-blox ZED-F9P, this MicroMod carrier gives your project high-precision GNSS and RTK positioning in a swappable, solderless MicroMod format. It supports rover and base station operation, with RTK accuracy down to millimetre-level positioning when used with suitable correction dat...

SKU: SF-DEV-10899

The LilyTiny is a compact LilyPad board with a built-in ATtiny85 microcontroller that drives four pre-programmed LED patterns. Simply sew on four LEDs and connect a battery — no programming or main board required. Each of the four output pads produces a different lighting effect: heartbeat pulse...

SKU: AF-3673

This kit is designed for use with the electronic textiles unit in the Exploring Computer Science (ECS, exploringcs.org) introductory computing curriculum for secondary students. It contains most of the materials needed for four e-textiles projects: paper circuit, wristband, mural, and hum...

SKU: AF-4308

A flexible electric heating pad made from stainless steel fibre fabric. Apply 5–12V DC and it warms up — temperature varies with voltage. Lightweight and flexible enough to wrap around objects or integrate into wearable projects. Essentially a large flexible resistor, it can be driven with PWM v...

SKU: LB-LR0183

A LilyPad-compatible microcontroller board based on the ATmega32U4, designed for e-textile and wearable electronics projects. The built-in USB communication allows the board to appear as a mouse, keyboard, or virtual serial port when connected to a computer — no separate USB-to-serial adapter nee...

SKU: DF-FIT0926

This high-brightness flexible filament has a diameter of only 2mm and a length of 600mm. It is composed of 320 LEDs and can be used for DIY lighting decoration and 360° all-angle lighting fixtures. It requires a power supply of 12V and comes with adjustable brightness. The small round hole end is...