All Products

SKU: AF-3263

The Adafruit Universal Thermocouple Amplifier MAX31856 Breakout reads temperature from virtually any thermocouple type — K, J, N, R, S, T, E, or B — with 0.0078125°C resolution and a measurement range of -210°C to +1800°C. It handles cold-junction compensation, linearisation, and fault detection ...

SKU: AF-1778

The AD8495 from Analog Devices is an analog-output K-type thermocouple amplifier on a compact breakout board. Simply power the board with 3–18V DC, connect a K-type thermocouple to the terminal block, and read the temperature as a voltage on the OUT pin — no digital protocols or complex configura...

SKU: DF-SEN0656 · MPN: SEN0656

The CT1780 is a cold-junction compensated amplifier for K-Type thermocouples, designed to make extreme temperature measurement easier to add to microcontroller projects. It digitises the tiny thermocouple signal and provides temperature readings with 0.25℃ resolution over a very wide measurement ...

SKU: AF-1727

The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts to share a single data line — ideal for multi-point temperature measurement. The...

SKU: DF-DFR0558

This Gravity I2C high-temperature sensor pairs a signal amplification module (MAX31855K) with a stainless steel sheathed K-type thermocouple probe for measuring temperatures up to 800 °C. The module converts the thermocouple's millivolt signal to a 14-bit digital reading over I²C, with cold-junct...

SKU: AF-269

The MAX31855 Thermocouple Amplifier Breakout converts K-type thermocouple readings into digital data via SPI, handling cold-junction compensation automatically. It measures temperatures from −200°C to +1350°C in 0.25°C increments, making it suitable for a wide range of temperature monitoring appl...

SKU: AF-5870 · MPN: ADA5870

This compact breakout adds a high-resolution, single-channel ADC to your I2C bus, making it a handy choice for precision differential measurements. It is built around the MCP3421, a simple and low-cost 18-bit ΔΣ converter with adjustable gain, a built-in precision reference voltage, and support f...

SKU: AF-270

A Type-K thermocouple with fiberglass braid insulation, rated to 500°C — far beyond the ~200°C limit of standard vinyl-insulated thermocouples. The bare bead probe design is suited to measuring both air and surface temperatures in high-heat environments such as ovens, kilns, heaters, and industri...

SKU: SF-SEN-16295

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: SF-SEN-16294

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: AF-3245

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare wires stainless-steel tip probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200°C, this one uses a fiberglass braid so...

SKU: AF-3328

The Adafruit PT100 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter. It reads 2-, 3-, or 4-wire PT100 platinum resistance temperature detectors over SPI, delivering laboratory-grade temperature accuracy and repeatability that surpasses therm...

SKU: SF-SEN-13266

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and...

SKU: AF-3984

For precision temperature sensing, nothing beats a Platinum RTD. Resistance temperature detectors (RTDs) are temperature sensors that contain a resistor that changes resistance value as its temperature changes, basically a kind of thermistor. In this sensor, the resistor is actually a small st...

SKU: AF-3648

The Adafruit PT1000 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter, configured for PT1000 platinum resistance temperature detectors. It reads 2-, 3-, or 4-wire PT1000 sensors over SPI, delivering laboratory-grade temperature accuracy and r...

SKU: AF-4535

The Adafruit HTS221 is an affordable I²C/SPI temperature and humidity sensor breakout board from ST. It measures relative humidity from 0–100% RH with 3.5% accuracy (in the 20–80% range) and temperature from -40 to 120°C with ±0.5°C accuracy (between 15 and 40°C). An excellent choice for everyday...

SKU: SF-PRT-13612

This Thermocouple Connector is perfect for bridging the gap between Type-K thermocouples with standard connectors with a PCB. This little connector is actually the exact part we recommend using with our SparkFun Thermocouple Breakout! Each connector can easily attach to a printed circuit board...

SKU: AF-5046

The BME688 from Bosch delivers comprehensive environmental sensing in a single compact package. This precision sensor measures temperature, humidity, barometric pressure, and VOC gas levels, all accessible over I2C or SPI. The BME688 is a drop-in replacement for the BME680, adding a programmable...

SKU: AF-1552

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 2.1W channels into 4 ohm impedance speakers (@ 10% THD). Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when...

SKU: DF-SEN0139

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them. You just need an additional IC (Like an AD595) for interpeting the data from this sensor. SPECIFICATIONS Measure...