All Products

SKU: PL-2884

The Pololu D24V150F9 is a high-current synchronous step-down (buck) voltage regulator that converts input voltages up to 40V down to a fixed 9V output. With up to 15 A available output current and typical efficiencies of 80–95%, it's well suited for powering large loads like motors, LED arrays, a...

SKU: PL-3216

A high-power 12V brushed DC gearmotor in the Pololu 25D form factor (25mm diameter) with a 34.014:1 metal spur gearbox and an integrated 48 CPR quadrature encoder. The encoder provides 1632.67 counts per revolution of the gearbox output shaft, enabling precise speed and position control for robot...

SKU: PL-2739

The Pololu AltIMU-10 v5 is a compact inertial measurement unit (IMU) and altimeter that combines a gyroscope, accelerometer, magnetometer, and barometric pressure sensor on a single board. It provides ten independent measurements — pressure, 3-axis rotation, 3-axis acceleration, and 3-axis magnet...

SKU: PL-2485

The Pololu Basic 2-Channel SPDT Relay Carrier provides simple, independent control of two single-pole, double-throw (SPDT) relay switches from low-voltage, low-current control signals. This assembled version comes ready to use with relays, terminal blocks, and header pins pre-soldered. Each rela...

SKU: PL-1268

The Pololu MinIMU-9 v2 is a compact (0.8″ × 0.5″) board that combines ST’s L3GD20 3-axis gyroscope and LSM303DLHC 3-axis accelerometer and 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore recommend careful reading of the L3GD20 datasheet (2MB pdf) and the LSM303DLHC da...

SKU: PL-3215

A high-power 12V brushed DC gearmotor with a 20.4:1 metal spur gearbox and integrated 48 CPR quadrature encoder. The encoder on the motor shaft provides 979.62 counts per revolution of the gearbox output shaft, enabling precise speed and position control for robotics applications. The cylindrica...

SKU: PL-2578

This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor. This high-brightness version draws an average of 16 mA at 5 V and has a typical sensing range up to approximately 24 inches (60&nb...

SKU: PL-1930

A pack of 100 female crimp pins designed for use with 0.1" (2.54mm) pitch crimp connector housings. Crimp these pins onto 22–28 AWG wires and snap them into housings to create custom cables compatible with standard headers and solderless breadboards. Key Features 0.1" (2.54mm) Pitch – Compatib...

SKU: PL-1120

A 200:1 plastic gearmotor with a 90-degree output shaft, offering a compact and affordable solution for small robot designs. The low-current brushed DC motor is well-suited for use with common motor drivers, and the recommended operating voltage range is 3–12V. The gearbox is fully enclosed and ...

SKU: PL-3070

A 1000:1 micro metal gearmotor from Pololu's popular N20-size range, featuring a high-power 6V brushed DC motor with long-life carbon brushes (HPCB). The carbon brushes offer significantly longer motor life compared to the precious metal brush (HP) version, while delivering the same performance. ...

SKU: PL-1100

A Pololu micro metal gearmotor with a 5:1 gear ratio and low-power (LP) 6V motor. The LP motor variant uses precious metal brushes and draws the least current of the micro metal gearmotor family, making it well-suited for battery-powered projects where efficiency matters more than peak torque. A...

SKU: PL-1094

A miniature low-power 6V brushed DC gearmotor with a 297.92:1 metal gearbox. With a 10 × 12mm cross section, this micro metal gearmotor delivers useful torque in an extremely compact form factor. The D-shaped output shaft is 3mm in diameter and extends 9mm from the gearbox. Key Features 297.92...

SKU: PL-1955

A pack of 25 steel, zinc-plated pan-head Phillips machine screws in the #2-56 thread size, 6.35 mm (1/4″) long. Commonly used in robotics, electronics enclosures, and small mechanical assemblies. Specifications Thread – #2-56 UNC (≈2.18 mm diameter, 0.45 mm pitch) Length – 6.35 mm (1/4″) Hea...

SKU: PL-2833

The compact (0.5″ × 0.7″) D24V10F9 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 85% and 93% and has a very l...

SKU: PL-1590

This Pololu 25D metal gearmotor combines a low-power 6V brushed DC motor with a 377.93:1 metal spur gearbox. The high gear ratio delivers substantial torque at low speed, making it well suited for applications that need strong, controlled movement rather than high RPM. The gearmotor uses the sta...

SKU: PL-2481

The Pololu basic relay carrier modules allow simple control of a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. This item includes the basic carrier PCB along with an Omron G5LE-14-DC5 5 V relay, 5.0 mm terminal blocks, and 0.1" male headers in s...

SKU: PL-1960

Steel zinc-plated pan-head Phillips machine screws, #4-40 thread, ¼" (6.35mm) long. Sold in a pack of 25. Ideal for securing PCBs, standoffs, and enclosures in electronics projects. Specifications Thread: #4-40 Length: ¼" (6.35mm) Head Type: Pan-head, Phillips drive Material: Steel, zinc-pl...

SKU: PL-1576

A high-power 6V brushed DC gearmotor with a 98.78:1 metal spur gearbox. The cylindrical motor body measures just under 25mm in diameter, and the D-shaped output shaft is 4mm in diameter, extending 12.5mm from the gearbox face plate. Also available with an integrated encoder for closed-loop contro...

SKU: PL-3434

This is a full set of replacement gears for the Power HD High-Torque Servo 1501MG.

SKU: PL-2698

M3 Phillips head machine screws, 16 mm long. A common fastener size used in electronics enclosures, 3D printer assemblies, robotics builds, and general prototyping. Sold in a pack of 25. Specifications Thread Size: M3 (3 mm) Length: 16 mm Head Type: Phillips Quantity: 25 Ideal For Electr...