All Products

SKU: AF-4197

Add a crisp, paper-like display to your microcontroller project with the Adafruit 2.13" Monochrome eInk Breakout. This 250×122 pixel black-and-white eInk panel delivers excellent daylight readability and retains its image even with power completely disconnected — just like printed paper. An onbo...

SKU: AF-4567

The Adafruit 2.23" Monochrome OLED Bonnet gives your Raspberry Pi a bright, high-contrast display that's easy to read from across the room. Simply plug this pre-assembled bonnet onto any Pi with a 2×20 header and start displaying sharp white text, graphics, and animations at up to 30 FPS. With 1...

SKU: AF-1429

Control 24 channels of 12-bit PWM output with the Adafruit TLC5947 breakout board. Designed for LED control, this SPI-driven board delivers constant-current open-drain outputs that keep brightness consistent even if the power supply dips. The chainable design lets you connect as many boards as yo...

SKU: AF-5146

The Adafruit 24LC32 I2C EEPROM Breakout provides 32 Kbit (4 KB) of reliable, non-volatile storage over a simple I2C interface. Store calibration values, MAC addresses, access tokens, or any data that needs to persist through power cycles and firmware updates — without the page-write constraints o...

SKU: AF-2478

Add a full-colour touchscreen to your project with this 2.4" TFT LCD breakout. The 240×320 pixel display delivers vivid RGB colour with individual pixel control, driven by the ILI9341 controller with built-in RAM buffering so your microcontroller does minimal work. A resistive touchscreen overlay...

SKU: AF-1028

Add a large, vibrant tri-colour eInk display to your microcontroller project with this 2.9" breakout board. The panel displays red, black, and white pixels at 296×128 resolution that remain visible even with power completely disconnected — just like printed paper, but with the added impact of col...

SKU: AF-5825 · MPN: ADA5825

This square TFT module is for advanced display projects that need a high-resolution, 3.4 inch IPS panel with a 480 x 480 pixel layout. It delivers 16-bit full-colour output and wide off-axis viewing, making it a neat fit for compact dashboards, controls and custom embedded interfaces.The display ...

SKU: AF-5808 · MPN: ADA5808

This square TFT module is made for advanced display projects that need a high-resolution, compact screen. It has a 3.4 inch IPS panel with 480x480 full-colour pixels, giving a crisp square format with good colour visibility off-axis.The display uses an ST7701S driver with SPI for configuration an...

SKU: AF-6414 · MPN: ADA6414

This 3.52" quad-colour eInk display delivers four distinct ink colours — red, black, yellow, and white — at 340×180 pixel resolution. The display retains its image with no power draw, offering the paper-like readability of standard eInk with an extra colour channel for richer, more informative gr...

SKU: AF-3106

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in blue. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall blue 7-segment display with decimal points and a centre colon for clock displays. ...

SKU: AF-3088

The Adafruit 4-Digit 7-Segment LED Matrix Display FeatherWing makes it easy to add a numeric display to any Feather project. The HT16K33 driver handles all LED multiplexing over I2C, so your Feather only needs two shared pins — leaving all other GPIO free for sensors, buttons, and additional disp...

SKU: AF-3108

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in red. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall red 7-segment display with decimal points and a centre colon for clock displays. Th...

SKU: AF-3109

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in white. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall white 7-segment display with decimal points and a centre colon for clock displays....

SKU: AF-3110

Add a bright, easy-to-read numeric display to your Feather project with the Adafruit 4-Digit 7-Segment FeatherWing in yellow. This combo pack includes the HT16K33-based FeatherWing backpack and a matching 0.56" tall yellow 7-segment display with decimal points and a centre colon for clock display...

SKU: AF-4352

Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...

SKU: AF-4339

This laser-cut acrylic enclosure kit turns your 4×4 NeoTrellis setup into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside the NeoTrellis RGB Driver PCB. The enclosure inclu...

SKU: AF-1492

Break out those tricky 0.5 mm pitch flex cable connections to breadboard-friendly 0.1" spaced headers with this FPC adapter board. The 50-pin connector on top accommodates most ZIF and snap-style FPC connectors, and each pin is broken out to a standard 0.1" × 0.1" header pad for easy prototyping....

SKU: AF-5963 · MPN: ADA5963

The Adafruit 555 PWM Output STEMMA is a fully assembled 555 timer board that generates an adjustable square-wave PWM signal — no breadboard wiring or external components needed. An onboard trimmer pot lets you tune the frequency across two selectable ranges: approximately 1.5 KHz to 25 KHz, or 1....

SKU: AF-5646

Add a dazzling 5×5 grid of 25 addressable RGB NeoPixels to any QT Py or Xiao board with this compact BFF (Best Friend Forever) add-on. The tiny SK6805 LEDs (1.5 × 1.5 mm each) pack vivid colour into a minimal footprint, powered directly from the QT Py's USB Type-C connection. The PCB is designed...

SKU: AF-1465

Stop searching for the AVR ISP pinout every time you program. This simple breakout adapter converts the standard 2×3 AVR ISP box header to two breadboard-friendly 1×3 rows, making it easy to wire up your programmer without crossed wires or guesswork. The adapter plugs neatly into any standard br...