All Products

SKU: EF-EF04027

Octopus Soil Moisture Sensor Brick can read the amount of moisture present in the soil surrounding it. It's a low tech sensor, but ideal for monitoring an urban garden, or your pet plant's water level. This is a must have tool for a connected garden!This sensor uses the two probes to pass curr...

SKU: EF-EF09086

SKU: EF-EF08207

Wukong is a high integrated breakout board with multiple functions based on micro:bit, which has a similar size with the micro:bit with buzzer, servo and motor drivers on board. The base board designs with standard 7x5 square bricks that can adapt perfectly to Lego.

SKU: EF-EF08209

Documents Smart Cutebot kit

SKU: EF-EF03426

IOT:bit is an expansion board based on IoT for micro:bit. It uses ESP8266 as WIFI expansion board and serial port to communicate with micro:bit. It also has extended all available IO port of the micro:bit which is leaded by GVS and you can extent various 3V E-blocks as LED, photosensitive and ser...

SKU: EF-EF10095

A 2×AA battery holder designed specifically for the BBC micro:bit. The built-in JST PH connector plugs directly into the micro:bit's battery socket, and the integrated on/off switch with a secure cover provides safe, convenient power control. Key Features micro:bit Compatible – JST PH connecto...

SKU: EF-EF09081

EF90D is a kind of 360 deg analog servo. It is light and portable, a little bigger than 5 cent coin. It works at 3V voltage and uses pulse width to adjust speed of the servo rotation, which also can be used to make small robot modules, mechanical arm modules and intelligent car modules. Parame...

SKU: EF-EF03415

The sensor:bit is a breakout board for the BBC micro:bit that extends all available I/O ports into standard GVS (Ground-Voltage-Signal) pin headers. This makes it easy to connect 3 V electronic modules like LEDs, photocells, servos, and other sensors without a breadboard. The board also features ...

SKU: EF-EF04089

Sonar:bit is a 3-wire ultrasonic distance sensor designed for micro:bit and Arduino projects. Operating on 3–5V, it works directly with both 3.3V and 5V systems using a single GVS cable — saving an I/O port compared to traditional 4-wire ultrasonic modules. With a measurement range of 4–400cm an...

SKU: EF-EF02053

Basic:bit is a basic breakout board of micro:bit. It carries a buzzer and three groups of GVS pins(P0/P1/P2) on board. Each group of GVS pins separately leads out the IO port, 3V port and GND port on micro:bit. Small size with simple structure, it is quite enough for you to complete 98% micro:bit...

SKU: EF-EF04098

This NeoPixel-compatible rainbow LED strip features 10 individually addressable WS2812B RGB LEDs with a standard 3-pin GVS connector for easy plug-and-play use. Both ends have connectors, allowing multiple strips to be daisy-chained for longer runs. Designed to work with micro:bit at 3.3V, it's ...

SKU: EF-EF04091

Octopus Single RGB Rainbow LED is one of the single rainbow LED electronic bricks in OCTOPUS series. The basic design is upon the OCTOPUS electronic bricks series with the identical design on the outlook, PCB fixed orifices and the connectors of the electronic bricks. The on-board LED is a ...

SKU: EF-EF11096

Specially designed to connect to seeed studio sensors, seeed Sudio sensors can be used on sensor:bit, octopus:bit, Wukong or other expansion boards. Only ordinary seeed studio sensors can be connected, IIC devices can not be used.

SKU: EF-EF04092

The Octopus Light Sensor Brick reads the ambient light level of its surrounding environment and outputs an analog signal. The 3-pin GVS connector makes it easy to plug into micro:bit expansion boards, Arduino, and other microcontrollers without soldering. Key Features Output – Analog signal pr...

SKU: EF-EF04058

A common cathode alphanumeric LED display module driven by the HT16K33 chip over I2C. The 0.56-inch digit height makes it suitable for displaying letters, numbers, and basic symbols in electronics projects and interactive displays. Key Features HT16K33 Driver – I2C bus interface for simple mic...

SKU: EF-EF04093

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the same.It can measure the total UV intensity of the sunlight; linear signal volta...

SKU: EF-EF04017

Octopus Electronic Bricks, you can use them to build electronics projects just as easy as piling bricks. By using Octopus electronic bricks, you may connect Arduino / Freaduino compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connect...

SKU: EF-EF03423

The Ring:bit expansion board is a simple PCB for the micro:bit. The Ring:bit extends the micro:bit's 3 GPIO ports. We will use this module to convert the P0/P1/P2 port to the common GVS port. It can be loaded 3 AAA batteries to drive the car or other components.FeatureCompatble with LEGO holeEach...

SKU: EF-EF09085

SKU: EF-EF08198

Smart home Kit is a product about smart home project base on micro:bit which is developed by ELECFREAK. We selected executed components commonly used at home as TMP36 temperature sensor, sound sensor, crash sensor, servo, motor. You can build scene like windowsill, wardrobe and fish tank, crea...