All Products
Showing 41-58 of 58 products · 2 unavailable products hidden
Gravity: Analog Turbidity Sensor For Arduino
The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended solids (TSS) in the water. The sensor provides both analogue (0–4.5V) and digit...
Gravity: Arduino ORP Meter V1.0
In the ever-increasing need and awareness for health and safety, water has become a focus point for proper disinfection treatment as aftereffects of industrialization can become a danger for contamination of water via direct contact. Water is a critical control point of contact where proper t...
Gravity: IIC Ozone Sensor (0-10ppm)
The Gravity IIC Ozone Sensor measures ozone (O₃) concentration from 0 to 10 ppm with 10 ppb resolution using an electrochemical sensing element. Factory-calibrated for accurate readings out of the box, it connects via I2C through DFRobot's Gravity 4-pin interface. Compatible with Arduino, ESP32,...
Gravity: I/O Expansion Shield for Pyboard
The Gravity I/O Expansion Shield for Pyboard connects your Pyboard v1.1 to the DFRobot Gravity sensor and module ecosystem with colour-coded plug-and-play connectors. No soldering is required — simply plug Gravity-compatible sensors and modules into the clearly labelled ports. An onboard externa...
Gravity: Digital I2C Signal Isolator
Gravity: Digital Signal Isolator is capable of isolating I2C digital signal and providing isolated power to the sensor module, effectively preventing mutual interference between the sensor modules. This digital signal isolator can be used for multi-parameter water quality detection systems to pre...
Gravity: Analog Signal Isolator
The Analog Signal Isolator can isolate analog signal and provide isolated power to sensors. It can effectively prevent sensor signal interference and apply to multi-parameter water quality monitoring sensors. Because usually sensors will be interfered by the other sensors during the measurement,...
Gravity: IO Sensor Shield For Arduino Mega Due
Say goodbye to messy cables and clueless pluging/unpluging! This Sensor Shield is a powerful expansion shield for Arduino Mega Due. It is large enough to carry up to 3 Xbee slots, 1 microSD slot and shield headers for most Arduino shields on the market. Besides, we also added a prototyping ar...
DFRobot Building Block Expansion Board Bundle for UNIHIKER M10
·
This bundle adds motor, servo and sensor expansion to the UNIHIKER M10 single-board computer, using the included Type-C to HY2.0-4P communication cable to bridge the M10 to the expansion board.The board includes an integrated 18650 battery holder so your controller, motors and sensors can run fro...
Gravity: Digital 1-to-8 I2C Multiplexer
The Gravity I2C Multiplexer solves address conflicts when you need to connect multiple I²C devices that share the same fixed address. It provides eight independent I²C ports on a single bus, allowing up to eight identical-address sensors or modules to communicate without conflict. The default I²...
Gravity: Water Flow Sensor (1/2) For Arduino
INTRODUCTION The Gravity Water Flow sensor measures the rate of a liquid flowing through it. The YF-S201 water flow sensor consists of a plastic valve body, flow rotor and hall effect sensor. It is usually used at the inlet end to detect the amount of flow. When liquid flows throug...
Qwiic to Gravity Cable - JST-SH to JST-PH (200mm, 28 AWG) - SparkFun Electronics
·
With the SparkFun Qwiic Connect System expanding every day, we want to make sure it becomes as accessible as possible but we understand there are other systems that can compliment it out there. The Qwiic to Gravity Adapter Cable allows interoperability between the SparkFun Qwiic Connect Syste...
Gravity: 4-Digital LED Segment Display Module (Green)
The Gravity 4-Digital LED Segment Display Module features a bright green 7-segment display with four digits, perfect for showing numbers, time, sensor readings, and other data in your projects. It communicates over I2C for simple two-wire connectivity with Arduino, Raspberry Pi, and other microco...
Gravity: Arduino Shield for Raspberry Pi B+/2B/3B/3B+/4B
The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...
Gravity 4-Pin M/M DuPont Cable with Tags - 30cm (5 Pack)
·
This 5 pack of labelled 4-pin male-to-male DuPont cables is designed to make wiring Gravity modules, breadboards and development boards clearer during prototyping. Each 30 cm cable includes printed I2C and UART pin tags on the wires, helping you identify power, ground and signal lines without rel...
Gravity: I/O Expansion Shield for OpenMV Cam H7 & H7 Plus
Gravity: I/O Expansion Shield for OpenMV Cam H7 & H7 Plus is an expansion shield specially designed for the OpenMV Cam H7 and OpenMV Cam H7 Plus. It is compatible with various sensors and electronic modules of Gravity series, plug and play, no soldering required. It not only helps you avoid the c...
Gravity LED Self-Locking Switch - Red
·
This illuminated pushbutton module is a simple self-locking switch with a built-in red LED for clear visual feedback. Press it once and the module outputs High while the LED turns on; press it again and the output goes Low while the LED turns off.It is designed for easy use in Arduino, micro:bit ...
Gravity: I2C 16x2 Arduino LCD with RGB Font Display (Black)
The Gravity I2C 16×2 LCD features RGB font colours on a black background, allowing you to display text in any of 16 million colour combinations. Using the Gravity I2C interface, only two data lines are needed for both communication and backlight control. The display supports 2 rows of 16 charact...
Gravity: I2C Triple Axis Accelerometer - LIS2DH
DFRobot presents the ultra low-power Arduino triple axis accelerometer! This device is based around a MEMS LIS2DH chip solution and has high-performance ultra-low power mode. The module is fitted with a Gravity I2C interface for easy plug and play integration in to your projects. The build in...
