All Products

SKU: DF-SEN0098-V2 · MPN: SEN0098-V2

##Introduction This is an updated version. Retired Product: Gravity: Analog 50A Current Sensor (AC/DC) V1Get this low-power current sensor to monitor your project every second for saving energy or protecting the circuit!This fully integrated Hall Effect-based linear STK-600/M current sensor gives...

SKU: DF-TEL0180 · MPN: TEL0180

The Gravity: WiFi IoT Module is a companion accessory for the Gravity: Science Data Acquisition (SCI DAQ) Module, enabling wireless sensor data transmission to IoT platforms without any programming required. Simply connect sensors to the SCI DAQ module and start uploading data instantly. Operati...

SKU: DF-MBT0008

The micro:IO Extender is a compact expansion board for the BBC micro:bit that breaks out all 19 I/O pins as Gravity-compatible 3-pin headers. It provides plug-and-play access to the full range of micro:bit GPIO, along with dedicated I2C and serial port headers, an onboard buzzer with switch, and ...

SKU: DF-SEN0388

This is a non-contact ultrasonic ranging sensor of high-performance from URM09 series, employing standard PH2.0-3P Gravity vertical interface. It provides an accuracy of 1% within an effective measuring range of 2~500cm(test on a flat wall). Similar to SR04 ultrasonic ranging modules in principle...

SKU: DF-DFR0327

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to all standard Arduino shields and sensors alongside the Pi's own GPIO, I2C, SPI, ...

SKU: DF-DFR0265

The DFRobot Gravity IO Expansion Shield V7.1 simplifies Arduino prototyping by breaking out all digital and analogue pins into colour-coded 3-pin (Signal, Voltage, Ground) Gravity connectors. Plug in sensors, actuators, and modules directly — no soldering or breadboard wiring required. Version 7...

SKU: DF-FIT0514

These wire offers you the best way to connect sensors and actuators to your LattePanda! They are specially designed for LattePanda and DFRobot Gravity Sensors. It compatible with a wide range of Gravity sensors and is easy to connect thanks to the unique anti-reverse-polarity design. It incl...

SKU: DF-TEM2022B-EN-1

An all-in-one IoT starter kit built around the FireBeetle 2 ESP32-E, designed by Hackster and DFRobot for learning IoT development with Arduino. The kit includes sensors, actuators, an audio player with speaker, and an I/O shield — everything needed to build connected projects right out of the bo...

SKU: DF-DFR0029-B

The Gravity Digital Push Button (Blue) is a simple momentary push button module designed for the DFRobot Gravity interface. It features an onboard LED indicator, immersion gold PCB surface, and a coloured button cap. A "D" marking on the board identifies it as a digital sensor for quick wiring re...

SKU: DF-DFR0469

A high-precision I2C real-time clock (RTC) module from DFRobot's Gravity series, based on the SD2405AL chip. It features an internal rechargeable battery that keeps time for 5–8 years without external power, making it ideal for data logging, alarm clocks, and any project that needs reliable timek...

SKU: DF-SEN0214

The Gravity Analog 20A Current Sensor measures both AC and DC current using the Hall effect, outputting a proportional analog voltage to your microcontroller. With high-voltage isolation built into the circuit design and a non-conductive acrylic base plate, it's designed for safe use in automatio...

SKU: DF-SEN0205

A photoelectric liquid level sensor that uses optical principles to detect the presence or absence of liquid. With no moving parts, it requires minimal calibration and offers high sensitivity and long service life. The corrosion-resistant polycarbonate probe handles temperatures from −25 °C to 10...

SKU: DF-DFR0645-G

The Gravity 4-Digital LED Segment Display Module features a bright green 7-segment display with four digits, perfect for showing numbers, time, sensor readings, and other data in your projects. It communicates over I2C for simple two-wire connectivity with Arduino, Raspberry Pi, and other microco...

SKU: DF-SEN0451 · MPN: SEN0451

This industrial Gravity kit measures electrical conductivity in aqueous solutions, helping you evaluate water quality by tracking dissolved content or salinity. It is suited to hydroponics, aquaculture and environmental water monitoring where long-running measurements are needed.The pro probe is ...

SKU: DF-DFR0577

The Gravity I/O Expansion Shield for Pyboard connects your Pyboard v1.1 to the DFRobot Gravity sensor and module ecosystem with colour-coded plug-and-play connectors. No soldering is required — simply plug Gravity-compatible sensors and modules into the clearly labelled ports. An onboard externa...

SKU: DF-DFR0053

This arduino Slide Position Sensor is based on straight-slip slide potentiometer sensor. The sensor is able to give provide the position of the slider which is often considered as a linear potentiometer . The sensor includes two analog outputs to allow the user to average the values and m...

SKU: DF-SEN0130

The Gravity MQ5 gas sensor is highly sensitive to LPG, natural gas, and town gas, with lower sensitivity to alcohol, cooking fumes, and cigarette smoke. The analogue output is proportional to gas concentration, and sensitivity can be adjusted via the on-board potentiometer. Gravity interface for ...

SKU: DF-DFR0556

A 16×2 character LCD display module from DFRobot's Gravity series, connecting to your Arduino or microcontroller via a simple I²C interface — just two data wires instead of the many parallel connections a standard LCD1602 requires. Compatible with both 3.3V and 5V, with no contrast adjustment nee...

SKU: DF-MBT0044-1 · MPN: MBT0044-1

This bundle adds motor, servo and sensor expansion to the UNIHIKER M10 single-board computer, using the included Type-C to HY2.0-4P communication cable to bridge the M10 to the expansion board.The board includes an integrated 18650 battery holder so your controller, motors and sensors can run fro...