All Products

SKU: SF-CAB-11579

Behold, the Hydra! This USB power cable probably looks a lot like something you’ve hacked together before. We do it all the time, because what is a computer if not a 5V power supply that happens to run software? The Hydra brings the 5V and GND lines from your USB power supply, computer or oth...

SKU: SF-TOL-11784

Are you frustrated with the lack of dexterity from most third hands? The SparkFun Third Hand gives you the ability to hold a board between two alligator clips on two flexible arms with multiple points of articulation. The arm’s wide range of articulation gives you access to any angle of the bo...

SKU: SF-TOL-12033

A parts kit for building or repairing an additional arm on the SparkFun Third Hand soldering helper. Includes alligator clips and the hardware needed to convert a coolant hose segment into a flexible helping hand. Ideal For Adding extra arms to the SparkFun Third Hand Replacing broken or worn c...

SKU: SF-TOL-09317

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...

SKU: AF-1222

The Adafruit GEMMA V2 is a tiny, coin-sized wearable microcontroller board powered by an ATtiny85 processor. At just 28 mm in diameter, it's small enough to fit into any sewable or wearable project, and affordable enough to dedicate to every build. Program it over USB with the Arduino IDE and bri...

SKU: AF-2024

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — attach one end to the shield and the other to any conductive object like metal, fru...

SKU: AF-2340

The Adafruit Capacitive Touch HAT adds 12 capacitive touch sensors to your Raspberry Pi using the MPR121 touch controller over I2C. Each sensor has a figure-8 hole designed for alligator clip connections — attach clips to the HAT and the other end to anything conductive (metal, fruit, vegetables,...

SKU: AF-1849

Get started with wearable electronics using the Adafruit Gemma Sensor Starter Pack. This all-in-one kit includes a GEMMA V2 board, sewable RGB NeoPixels, multiple sensors, a rechargeable battery with charger, and everything you need to build interactive sewable projects — no soldering required. ...

SKU: AF-1657

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four sewable bright RGB pixels, a battery holder and batteries, 2-ply conductive thread, alligator clips to help you test out your circuit, and a U...

SKU: AF-3670

High-conductive heating fabrics are Literally! This non-woven fabric feels a little like felted paper but is filled with conductive material that can make the fabric emit heat when powered. Resistive heating fabrics safely deliver comfortable conductive and radiant heating at low voltage thr...

SKU: LB-00240

FunKey is a new product series from Architectronics that extends the functionality of another familiar touch board and is better designed, more affordable and simpler to use. FunKey Simple: 18 keystrokes easily reconfigured to any keystrokes using simple app all alligator, no "headers" touch...

SKU: AF-1466

This UL-listed switching power supply delivers a clean, regulated 5V DC output at up to 4A (4,000mA / 20W) via a standard 5.5×2.1mm centre-positive DC barrel jack. It accepts 110–240V AC input and is ideal for powering LED matrices, NeoPixel strips, and other high-current 5V projects. Key Featur...

SKU: AF-3915

Keep your Circuit Playground Express safe in this snap-together acrylic enclosure. Designed by Ada-friend Mike Doell, this minimal but elegant case turns your board into an electronic snowflake shape with no tools required for assembly. The enclosure provides full access to all buttons, the slid...

SKU: LB-LS0823

The Micro: bit GPIO T-type Expansion Board is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pin. This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:...

SKU: MM-SKU00063

With this kit, you get everything you need to start learning about connecting electronics to your micro:bit in an accessible and easy manner. Everything is connected using the supplied alligator clips, so no soldering required. This kit suitable for children as young as 10 with some adult help...

SKU: AF-3989

Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read quickly.This Large 3V Panel Meter is about handheld-size, with one screw to open up the panel and replace the backing paper, if you like.Even though i...

SKU: AF-3990

Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read quickly.This Large 5V Analog Panel Meter is about handheld-size, with one screw to open up the panel and replace the backing paper, if you like.E...

SKU: AF-1405

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic project. There's a Flora motherboard, four ultra-bright chainable RGB pixels, a 3x...

SKU: LB-LS0818-LIGHT-BLUE

These soft rubber cases will protect your micro:bit while also looking super cute! It is made from hard-wearing, soft, flexible rubber, making it easy to fit or remove it. The white piece lets you see the labels on the edge connector and access the pads with alligator clips, or you can remove it ...

SKU: LB-SHAKEUP-STD

The ShakeUp makes you a STEAM inventor by helping you to connect everyday objects to your computer. If you can plug in a Keyboard and Mouse, you can use the ShakeUp.  The Magic Science When you plug the ShakeUp into your computer, your computer thinks it's just a regular keyboard and mous...