All Products

SKU: SF-TOL-18340

The digital multimeter (DMM) is an essential tool in every electronic enthusiasts arsenal. This Smart Digital Multimeter, however, is not your average multimeter, it features a continuity sound at less than about 40±5Ω, current/voltage sense, and a Smart Measurement feature. You can use the multi...

SKU: SF-PRT-09547

A 2×AA battery holder with a sliding cover secured by a Phillips head screw and a built-in ON/OFF switch for convenient power control. The 150mm tinned leads make it easy to solder into your projects. Key Features 2×AA Capacity – Provides 3V with alkaline batteries ON/OFF Switch – Built-in po...

SKU: AF-3521

A 3-pack of standard alkaline AA batteries for powering portable electronics, kits, and projects. These use alkaline (MnO2) chemistry with a voltage range of 1.6V (fresh) to 0.8V (depleted) and a typical capacity of approximately 3000mAh. Specifications Type – AA (LR6) Chemistry – Alkaline (M...

SKU: LB-PT12114

A compact, multi-purpose battery tester that quickly checks the charge level of common household batteries. The colour-coded analogue dial gives you an instant good/low/replace reading — no guessing whether that battery in the drawer still has juice. A movable arm accommodates different battery ...

SKU: AF-3349

A 4-pack of standard alkaline AA batteries for powering portable electronics, kits, and projects. These use alkaline (MnO2) chemistry with a voltage range of 1.6V (fresh) to 0.8V (depleted) and a typical capacity of approximately 3000mAh. Specifications Type – AA (LR6) Chemistry – Alkaline (M...

SKU: DF-FIT0079

A simple 4-cell AA battery holder in a square (2×2) configuration. Features 5-inch tinned leads for easy soldering into your project. Provides 6V nominal output with four AA alkaline batteries, or 4.8V with rechargeable NiMH cells. Specifications Battery Type – AA (LR6) Cell Count – 4 Config...

SKU: AF-1131

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs including LiPo, Li-Ion, and AAA battery holders. Key Features JST-PH 2-Pin Connectors...

SKU: DF-FIT0078

A double-layer 6×AA battery holder with a stacked 3+3 cell arrangement for a more compact footprint. Creates a 7.2V rechargeable battery pack from NiMH/NiCd cells or a 9V pack from alkaline cells. Comes with 150mm (6") red and black wire leads. Specifications Cell Quantity: 6× AA (double layer...

SKU: AF-3287

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST batte...

SKU: DF-FIT0141

A 6×AA battery holder with a DC 2.1mm power jack that plugs directly into an Arduino's barrel jack input. Creates a 7.2V rechargeable battery pack from NiMH/NiCd cells or a 9V pack from alkaline cells. Features mounting holes for secure installation. Specifications Cell Quantity: 6× AA Output...

SKU: DF-FIT0362

This battery holder can hold 3 AA batteries which provides 3.6V rechargeable battery pack with NiMH / NiCd cells or 4.5V battery pack with Alkaline cells. You will be able to power your Arduino with this battery holder via MicroUSB interface directly. SPECIFICATIONS Cell Quantity: 3 Battery type...

SKU: LB-LR0294

A simple 6-cell AA battery holder with a 125mm (5") cable terminated with a standard 5.5×2.1mm centre-positive barrel jack connector. Creates a 7.2V rechargeable battery pack from NiMH/NiCd cells or a 9V pack from alkaline cells, ready to plug directly into devices with a standard DC barrel jack ...

SKU: EF-EF08180

ElecFreaks Micro:bit Starter Kit is designed for people who is at the door step of learning electric circuit and programming knowledge. The kit has provided some basic electronic components like LED, button, buzzer, temperature sensor , steering engine and motor etc.. You can not only learn basic...

SKU: SF-PRT-00091

A classic 9V battery snap connector terminated with a 2-pin polarised Molex connector. Ideal for quick-connect battery power in breadboard and prototyping setups. Key Features Molex Terminated – 2-pin polarised connector for secure, reversible connections Cable Length – 5 inches (approximatel...

SKU: SF-DEV-21326 · MPN: DEV-21326

This compact MicroMod processor board adds an STM32F405 to a compatible MicroMod Carrier Board, giving your project an ARM® Cortex®-M4 32-bit RISC core in a small, swappable M.2 module.The bevelled edge connector keys into the MicroMod M.2 socket and is secured with the screw supplied with MicroM...

SKU: SF-KIT-29326 · MPN: KIT-29326

Start learning embedded electronics with a complete MicroPython kit designed for beginners. It guides you from blinking your first LED through to building and programming an autonomous robot, with no prior programming or electronics experience required.The kit is built around MicroPython, a begin...