All Products

SKU: DF-ROB0109

Sparki is a fully assembled, Arduino-compatible robot designed for learning programming, electronics, and robotics. Based on the Arduino Leonardo, it comes packed with sensors, motors, a display, and wireless connectivity — ready to use out of the box with no assembly required. Key Features Ar...

SKU: SF-COM-00315

The SN754410 is a quad half H-bridge motor driver IC capable of driving DC motors, stepper motors, and other inductive loads. It accepts TTL 5V logic inputs and can drive motors from 4.5V to 36V at up to 1A continuous output current per channel. A pin-compatible replacement for the popular L293D...

SKU: DF-FIT0223

A medium-sized aluminium heat sink with pre-applied 3M 8810 thermal adhesive tape on the back. Simply peel off the blue protective film and stick it directly onto your IC or chip — no thermal paste or glue required. The adhesive bond is strong and long-lasting. Suitable for stepper motors, motor...

SKU: LB-LR0180

Including CNC Shield V3.0The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors. Each channel of stepper motor only needs 2 I...

SKU: AF-1175

A machined aluminium flexible shaft coupler for connecting two 5mm shafts. The spiral-cut design provides slight flexibility to accommodate minor misalignment between shafts, reducing binding without introducing rotational backlash — making it suitable for precision CNC work. Key Features Flex...

SKU: YH-6000100127

The Super:bit is a feature-rich expansion board that transforms the BBC micro:bit into the core of robotics and LEGO-compatible projects. With support for DC motors, stepper motors, and servos, plus onboard RGB LEDs and a buzzer, it provides everything needed to build programmable robots — no sol...

SKU: EC-ARS27361T

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handled via the I2C bus, freeing up digital pins for other uses. The stackable design...

SKU: AF-5679

The Adafruit Floppy FeatherWing lets you read and write 3.5-inch or 5.25-inch floppy disks using a Feather microcontroller. It connects to standard 34-pin IDC floppy drives and includes built-in level shifting between 3.3 V Feather logic and the 5 V signals that floppy drives require. Floppy dri...

SKU: DF-DRI0054 · MPN: DRI0054

##Introduction The multifunctional motor driver expansion board is designed for Raspberry Pi Zero/Zero W/A+/B+/2B/3B/3B+/4B. This fully-featured robot motor expansion board is capable of supporting multiple motors, stepper motors, and servos simultaneously. It also provides spare camera and DIP d...

SKU: KI-5693

With the Kitronik Compact Robotics Board, the BBC micro:bit can be used to drive 4 motors (or 2 stepper motors) and 8 servos. Coupled with 17 other I/O expansion points, this means the BBC micro:bit can very easily become the core of a whole variety of robotics projects. The board is small on foo...

SKU: KI-5698

A compact motor driver board for the BBC micro:bit that drives two DC motors or one stepper motor. The integrated edge connector lets the micro:bit slot in directly, with built-in protection against short circuits, overcurrent, and overheating. Power is supplied via terminal block or servo conne...

SKU: DF-DFR0406

INTRODUCTION The Arduino Motor Shield is based on L298 (a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors). It helps you drive two DC motors with Arduino board as well as control the speed and direction of the ...

SKU: AF-3297

The Adafruit DRV8833 is a dual H-bridge motor driver breakout, capable of driving two DC motors bidirectionally or one bipolar/unipolar stepper motor at up to 1.2 A per channel. It's well suited for low-voltage applications, operating from 2.7V to 10.8V motor power. The DRV8833 features built-in...

SKU: AF-807

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....

SKU: AF-2448

The Adafruit TB6612 Breakout is a compact dual H-bridge motor driver that can spin two DC motors bidirectionally, step one bipolar or unipolar stepper, or fire two solenoids — all at up to 1.2A continuous per channel (3A peak). It's the same driver chip used in the Adafruit Motor Shield and Motor...

SKU: IT-IM120417005

Overview MotoMama is a Arduino shield based on L298N H-bridge driver chip. You can use this shield to drive two DC motors or an four-wire two-phase stepper motor.  For power supply , power terminal on board is available – it will also power the Arduino board.  Or from the power jack ...

SKU: AF-5129

Cytron's Maker Pi RP2040 features the new Raspberry Pi RP2040 chip embedded on a robot controller board. The board comes with a dual-channel DC motor driver, 4 servo motor ports, and 7 Grove I/O connectors. Now you can build your new robot friend while simultaneously trying out the new RP2040 chi...

SKU: AF-2653

Get your Particle (formally known as Spark) Photon moving with a PhoBot Robotics shield. No, this is not a robot that makes you a delicious bowl of Vietnamese soup.  Instead, it's a board from Simon Monk that's kind of like a Motorshield for your Spark Core or Particle Photon th...

SKU: PR-PIM688

A high-power modular robotics and engineering platform, built around RP2040 and designed to drive the most ambitious robots, props and devices. The Do-Everything Board 🦾 Yukon is a standalone controller that can be equipped with up to six interchangeable modules capable of driving high-powe...

SKU: AF-4225

Everything you need (besides the Jetson Nano) to build NVIDIA's JetBot — an open-source AI robot platform. This parts pack includes the motor driver, motors, wheels, and a handy PiOLED display to get your JetBot rolling. The included DC Motor + Stepper FeatherWing provides I2C control for two br...