All Products

SKU: SF-COM-11629

A smart 4-digit 7-segment display that combines a classic white LED display with an onboard ATmega328 microcontroller. Instead of wiring up dozens of pins, you control the entire display over Serial TTL, SPI, or I2C — using just a few connections. The ATmega328 comes pre-loaded with the Arduino ...

SKU: SF-BOB-10124

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount o...

SKU: SF-SEN-14520

The SparkFun Capacitive Touch Breakout provides a single momentary touch button using the AT42QT1011 capacitive sense chip. Simply supply 1.8–5 V and ground — the chip handles all touch monitoring and outputs a digital high signal when a touch is detected, low when released. Unlike the AT42QT101...

SKU: SF-PRT-08074

These are small spring terminals. Open the aperature with the small arm, insert the wire, release the arm and the wire is held firmly in place. This is a good quick way to to interface to bare wires. Capable of higher current and more resilient than breadboard or female header type connections. ...

SKU: SF-SEN-14722

This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the ref...

SKU: SF-SEN-15344

Do you want to replace a slider or a button on your art project or science experiment with a more interesting interface? This Capacitive Touch Slider is a "Qwiic" and easy way to add capacitive touch to your next project. With the board's built in touch pads, you can immediately start playing wit...

SKU: DF-FIT0576

This is a soft thin protoboard with hole diameter of 1mm, hole spacing of 2.54mm. It can be soldered DIP and SMD components, and the thickness is only 0.4mm. The proto board can be appropriate bending in any direction (depending on the size of the proto board). In the actual application, it can ...

SKU: SF-KIT-12963

The SparkFun Digital Sandbox Add-On kit extends the Digital Sandbox (DS) learning platform with three additional circuit experiments. Build an electric musical instrument, control motor speed, and drive a servo — perfect for learners who have completed the first 13 experiments and want more hands...

SKU: SF-LCD-16396

The SparkFun SerLCD is an AVR-based, serial enabled LCD that provides a simple and cost effective solution for adding a 16x2 Black on RGB Liquid Crystal Display into your project. We've seriously overhauled the PCB design on the back of the screen by including an ATmega328P that handles all of th...

SKU: AF-4785

A 3-pack of universal proto-board PCBs measuring 40 × 60 mm, made from sturdy FR4 fibreglass with a black silkscreen on both sides featuring row and column markings. Each board has 280 through-holes (14 columns × 20 rows) on a standard 2.54 mm pitch with no pre-connected traces — connections are ...

SKU: SF-COM-08236

This is a fully assembled simple breakout board for the surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down selections then select by pressing the plastic piece inwards. Capable of swtiching ...

SKU: SF-TOL-12033

A parts kit for building or repairing an additional arm on the SparkFun Third Hand soldering helper. Includes alligator clips and the hardware needed to convert a coolant hose segment into a flexible helping hand. Ideal For Adding extra arms to the SparkFun Third Hand Replacing broken or worn c...

SKU: SF-LCD-16398

The SparkFun SerLCD is an AVR-based, serial enabled LCD that provides a simple and cost effective solution for adding a 20x4 Black on RGB Liquid Crystal Display into your project. We've seriously overhauled the PCB design on the back of the screen by including an ATmega328P that handles all of th...

SKU: SF-GPS-17285

The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter ac...

SKU: SF-BOB-11040

The SparkFun LED RingCoder Breakout provides a visual position indicator for rotary encoders. Two 8-bit shift registers drive a circular LED bargraph that displays the virtual position of the encoder as it turns, giving clear feedback on where you are within a range of values. This RGB revision ...

SKU: SF-PRT-08073

These are small spring terminals. Open the aperature with the small arm, insert the wire, release the arm and the wire is held firmly in place. This is a good quick way to to interface to bare wires. Capable of higher current and more resilient than breadboard or female header type connections. ...

SKU: SF-PRT-16890

These are the surface mount 50 pin 0.5mm Board to Board Double Slot Female Connectors found on the Alchitry FPGA boards. These headers allow for Alchitry FPGA Boards to stack on one another by being soldered to the topside of the board.These connectors are sold in single units. Four of these conn...

SKU: SF-WRL-11373

The SparkFun XBee Explorer Regulated takes care of the 3.3V regulation, signal conditioning, and basic activity indicators (Power, RSSI and DIN/DOUT activity LEDs). It translates the 5V serial signals to 3.3V so that you can connect a 5V (down to 3.3V) system to any XBee module. The board was con...

SKU: SF-BOB-15439

The SparkFun PCA9306 Level Translator Breakout provides dual bidirectional voltage-level translation for I2C and SMBus lines. It lets you safely connect devices operating at different logic levels — for example, a 3.3V sensor to a 5V microcontroller — without a direction pin. Simply apply your re...

SKU: SF-SEN-15335

The SparkFun 9DoF IMU Breakout brings InvenSense's ICM-20948 9-axis motion tracking sensor to a Qwiic-enabled breakout board with an on-board logic level shifter and broken-out GPIO pins. The ICM-20948 is an extremely low-power sensor supporting both I2C and SPI communication, suited for wearable...