All Products

SKU: SF-DEV-12640

Here at SparkFun, we refuse to leave ‘good enough’ alone. That’s why we’re adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-...

SKU: DF-DFR0407

The Arduino 9 Axes Motion Shield is based on the Bosch BNO055 absolute orientation sensor — a System in Package (SiP) integrating a triaxial 14-bit accelerometer, 16-bit gyroscope (±2000°/s range), triaxial geomagnetic sensor, and a 32-bit microcontroller running BSX3.0 FusionLib software. The B...

SKU: AF-564

A small, portable inverter for EL wire. Powers off of 4 AAA batteries (not included!), it can drive 3-4 meters (10 to 13 feet) of our high-brightness EL wire OR 1 meter (3 feet) of EL tape OR a 10cmx10cm piece of EL panel for about 7 hours.There is a switch for selecting steady/blink/off modes...

SKU: DF-SEN0183

The CMPS11 is a 3rd-generation tilt-compensated magnetic compass module that combines a 3-axis magnetometer, 3-axis gyroscope, and 3-axis accelerometer. An onboard Kalman filter fuses gyro and accelerometer data to remove errors caused by tilting, delivering accurate heading readings regardless o...

SKU: DF-SEN0001

URM37 V4.0 Arduino Ultrasonic Sensor comes with temperature compensation which provides better distance measurement accuracy. It is very unique feature in the industry. URM37 V4.0 Arduino Ultrasonic Sensor offers output modes: analog output, switch, serial (TTL and RS232 level optional) and P...

SKU: SF-COM-10953

The MMA8452Q is a low-power, 3-axis capacitive MEMS accelerometer with 12-bit resolution. Packed with embedded motion-detection functions and configurable interrupt outputs, it can monitor events autonomously while staying in a low-power state — reducing the need for the host processor to continu...

SKU: SF-DEV-11113

It’s blue! It’s thin! It’s the Arduino Pro Mini! SparkFun’s minimal design approach to Arduino. This is a 5V Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommen...

SKU: SF-DEV-11114

It’s blue! It’s thin! It’s the Arduino Pro Mini! SparkFun’s minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We reco...

SKU: AF-3146

Create custom wire harnesses with these single-row housings for DIY jumper cables. Compatible with both male and female jumper wires, these housings give you full control over your wiring layout and connector configurations. Simply snap in raw jumper wires to build custom-length, custom-pin-coun...

SKU: AF-3145

A pack of 50 small single-row wire housings for building custom jumper cable harnesses. Compatible with both male and female crimp pins, these housings let you create exactly the wire configurations your project needs. Available in five sizes from 1-pin to 5-pin, they snap together easily with s...

SKU: AF-3144

Are you frustrated by the lack of customization options for your jumper wires? Look no further! Compatible with both male and female wires, these fully customizable wire housings bring DIY to a new level, giving you near limitless options when using jumper wires in your project. This is a pack...

SKU: AF-3143

A pack of small dual-row connector housings for building custom jumper cable harnesses. Compatible with standard 0.1" pitch raw jumper wire crimp pins — snap in your crimped wires and create exactly the connector configuration your project needs. Package Contents 5× 2×2 housing 5× 2×3 housing 5...

SKU: SF-DEV-13664

If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Mini Breakout is a great landing spot. The SAMD21 Mini Breakout is a Pro Mini-sized breakout for the Atmel ATSAMD21G18, a 32-bit ARM Cortex-M0+ processor with 256KB flash, 32KB SRAM, and an o...

SKU: AF-157

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just pass...

SKU: AF-3072

The Adafruit RFM95W LoRa Radio Transceiver Breakout lets you send data over very long distances using the 868 or 915 MHz licence-free ISM bands. Based on the SX1276 LoRa chipset, this breakout achieves ranges of approximately 2 km line of sight with a simple wire antenna — or up to 20 km with dir...

SKU: DF-SEN0142

A compact breakout board for the MPU-6050, combining a 3-axis gyroscope and 3-axis accelerometer with an onboard Digital Motion Processor (DMP) on a single chip. The integrated DMP handles complex motion fusion algorithms, offloading processing from your microcontroller. The breakout includes a ...

SKU: DF-DFR0159

The 5V DFduino Pro Mini V1.3(Arduino Pro Mini Compatible) is a microcontroller board based on the ATmega328.It is a 5V DFduino running the 16MHz bootloader (select 'Arduino Duemilanove w/ 328' within the Arduino software). It is an advance version of offical Arduino Pro Mini. The DFRd...

SKU: SF-DEV-09267

The LilyPad Accelerometer is a three-axis accelerometer based on the Analog Devices ADXL335, designed for the LilyPad wearable e-textile system. It detects joint movement, inclination, and vibration, outputting 0–3 V analogue signals on the X, Y, and Z axes. The board features large sewable pads...

SKU: AF-2407

Its a mini panel-mountable HDMI monitor with a built-in touchscreen! So small and simple, you can use this display with any computer that has HDMI output, and the shape makes it easy to attach to a case or rail. This backpack features the TFP401 for decoding video, and includes the attached displ...

SKU: AF-2353

This 7.0" TFT display packs 800×480 pixels with an LED backlight and 24-bit colour capability via its 40-pin connector (8 red, 8 green, 8 blue parallel pins). It's ideal for projects requiring a large display area for graphics, menus, or data visualisation. This is a raw pixel-dot-clock display ...