All Products

SKU: AF-1955

These Male/Male Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on either end and fit cleanly nex...

SKU: SF-PRT-08431

This is a SparkFun exclusive! These are 155mm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Combine these with our female to female jumpers to create a male to female jumper. Multiple jumpers can be installed n...

SKU: SF-DEV-27924 · MPN: DEV-27924

Control a project with muscle activity instead of buttons, levers or joysticks. The MyoWare® 2.0 Muscle Sensor is an all-in-one surface electromyography (sEMG) sensor that detects the electrical signals generated when a muscle flexes, then outputs an analogue signal representing the strength of t...

SKU: PI-CAB0001

Rainbow coloured jumper strips, perfect for use with our mini breadboards! At just 100mm in length this jumper jerky is ideal for use on a breadboard or in any situation where space is at a premium. Each strip of jerky contains 40 individual jumper leads, 100mm long, which are easily separated...

SKU: SF-CAB-13685

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based device’s pins.Wire length is 140mm (about 5....

SKU: PI-CAB0002

Rainbow coloured jumper strips, perfect for use with our mini breadboards! At just 100mm in length this jumper jerky is ideal for use on a breadboard or in any situation where space is at a premium. Each strip of jerky contains 40 individual jumper leads, 100mm long, which are easily separated...

SKU: LB-SOLAR-M

A compact micro solar panel rated at 1.5 V and 400 mA (0.65 W peak), fitted with pre-soldered male jumper wires for direct breadboard use. Its small 80×60 mm form factor makes it easy to integrate into DIY solar projects and prototyping setups. Key Features 1.5 V / 400 mA Output – 0.65 W peak ...

SKU: SF-PRT-10897

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Comes as 1 package of one hundred jumpers (colors shown). Note: The pictures for th...

SKU: SF-PRT-11710

Jumper wires are awesome. Just a little bit of stranded core wire with a nice solid female connector on either end. They have the flexibility of stranded wire but will fit directly onto male pin headers. The only downside to the standard jumper wires we carry is that they’re a tad too thin to use...

SKU: SF-PRT-11709

Jumper wires are awesome. Just a little bit of stranded core wire with a nice solid pin connector on either end. They have the flexibility of stranded wire but will fit directly into breadboards and female pin headers. The only downside to the standard jumper wires we carry is that they’re a t...

SKU: DF-DFR0518

Micro:Mate is a tiny micro:bit I/O expansion board for learning electronics and building DIY projects.Micro:Mate expands 6 sets of 3-pin I/O interfaces, capable of connecting DFRobot Gravity series modules, servo motors, sensors and jumper wires. Additionally, Pin 8, 12, 16 support voltage switch...

SKU: DF-FIT0890

TS80P is a smart soldering iron powered by USB Type-C PD2.0/QC3.0 standard input. It only takes 8 seconds to heat up from room temperature to 300°C. The temperature of the soldering iron tip can be adjusted at any time, and all operations can be completed with one hand.TS80P controller is made of...

SKU: PI-CAB0003

Rainbow coloured jumper strips, perfect for use with our mini breadboards! At just 100mm in length this jumper jerky is ideal for use on a breadboard or in any situation where space is at a premium. Each strip of jerky contains 40 individual jumper leads, 100mm long, which are easily separated in...

SKU: AF-266

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are a little over 6" (150mm) long and come in a 'strip' of 40 (4 pieces of each of ten colors). They have 0.1" sockets on either end and fit cleanly next to each other on standard-pitch 0.1" (2.54...

SKU: AF-1957

A set of 20 premium male-to-male jumper wires in a ribbon cable strip, each 150 mm (6") long. The wires feature 0.1" (2.54 mm) male header contacts on both ends and come in 10 rainbow colours (2 of each). Pull individual wires from the ribbon as needed, or keep them together for organised wire ha...

SKU: SF-SEN-11769

The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. By measuring the amount of reflected infrared light, it can detect transitions from light t...

SKU: SF-BOB-10031

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all 5 pins with a vertical microUSB connector for your prototyping needs. Documents: Schematic Eagle Files GitHub

SKU: AF-1953

These Female/Male 'extension' jumper wires for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbow colors). They have 0.1" male header contacts on one end and 0.1" female header ...

SKU: AF-4447

These premium female-female jumper wires are handy for making wire harnesses or jumpering between headers on PCBs. They're 200mm (~7.8") long and come loose as a pack of 40 (10 pieces of red, blue, yellow, and Adafruit black). They have 0.1" female header contacts on either end and fit cleanly ne...

SKU: DF-DFR1015

Multiple-output DC–DC converters are essential in a multitude of applications where different DC output voltages are required.This DC-DC step-down voltage power module converts 7.5V~30V input to an output of 3.3V/5V/9V/12V (default to 5V), which can be selected by short-circuiting the correspondi...