All Products

SKU: DF-FIT0810

A flexible LED filament chip that emits blue light in a full 360° pattern. At 260mm long and just 2mm in diameter, the filament can be bent and folded into any shape, making it perfect for DIY lighting decorations, custom lamp builds, and creative light installations. The small round hole at one...

SKU: LB-SOLAR

A compact micro solar cell rated at 1.5 V and 400 mA (0.65 W peak), ready to use with pre-soldered anode and cathode wires. Its small 80×60 mm form factor makes it well suited for DIY solar projects, battery charging experiments, and powering small loads like motors, LEDs, and light bulbs. Key F...

SKU: LB-SOLAR-M

A compact micro solar panel rated at 1.5 V and 400 mA (0.65 W peak), fitted with pre-soldered male jumper wires for direct breadboard use. Its small 80×60 mm form factor makes it easy to integrate into DIY solar projects and prototyping setups. Key Features 1.5 V / 400 mA Output – 0.65 W peak ...

SKU: AF-661 · MPN: 661

A compact 1″ diagonal OLED display with 128×32 white pixels driven by the SSD1306 controller. Each pixel is individually lit, delivering sharp, high-contrast graphics with no backlight needed — resulting in excellent readability and low power consumption. Communicates via SPI (4–5 pins required)...

SKU: AF-2190 · MPN: 2190

The VERTER is a buck-boost DC-DC converter that accepts 3–12 V input and outputs a stable 5.2 V — ideal for powering Arduino, Raspberry Pi, and other 5 V electronics from a wide variety of battery packs. The slightly elevated 5.2 V output provides headroom for voltage drop across USB cables and c...

SKU: DF-DFR0579

The Solar Power Manager Micro is an ultra-low-power solar energy management module designed for 1–3 V small solar panels. Built around the SPV1050 IC with MPPT (Maximum Power Point Tracking), it maximises solar conversion efficiency even under weak sunlight — enabling charge-free, battery-replace...

SKU: AF-865 · MPN: 865

A red 4-digit 7-segment clock display with 0.56″ (14.2 mm) digit height. Each digit includes a decimal point, plus a centre colon for time-based displays. Bright at 18 mcd, these displays are easy to read and can be dimmed by reducing drive current to save power. This is a raw multiplexed common...

SKU: AF-2465 · MPN: 2465

The PowerBoost 1000C is a DC/DC boost converter with a built-in LiPo battery charger and smart load-sharing circuit. It takes any 3.7V LiIon/LiPoly battery and boosts the output to 5.2V for powering 5V projects like Arduino, Raspberry Pi, or BeagleBone — even while the battery is charging. The l...

SKU: DF-DFR0399

A compact DC micro metal gear motor with a built-in driver that uses the DFRobot Gravity 3-pin interface. Simply connect to a microcontroller and control direction and speed with a single PWM signal — no external H-bridge required. The embedded driver accepts standard servo-style PPM signals, so...

SKU: AF-518 · MPN: 518

An ultra-bright 1 W cool white LED pre-mounted on an aluminium PCB heatsink, making it easy to solder and integrate into projects. With 90 lumens output in a 140° lambertian pattern, it delivers bright, even illumination ideal for flashlights, headlamps, and general lighting. The LED produces a ...

SKU: AF-3661 · MPN: 3661

The Adafruit MiniBoost is a tiny charge-pump voltage booster that converts 3–5 V input to a regulated 5 V output at up to 100 mA. About the size of a linear regulator, it's an easy drop-in solution for battery-powered projects running on 2–3 alkaline cells or a single lithium cell. Based on the ...

SKU: DF-SEN0503

An infrared break-beam sensor pair for simple, reliable motion detection. The emitter sends a beam of invisible IR light to the receiver — when an object passes between them and breaks the beam, the receiver outputs a signal. Works up to 50 cm at 5 V with a fast response time under 2 ms. The com...

SKU: AF-5177 · MPN: 5177

Dress up your mechanical keys in your favorite colors with a wide selection of gumdrop-like, retro, curvy, and stylish MA profile keycaps. Here is a 5 pack of Purple MA Keycaps for your next mechanical keyboard or NeoKey project. Snap 'em onto any Cherry MX or compatible switc...

SKU: AF-5174 · MPN: 5174

Dress up your mechanical keys in your favorite colors with a wide selection of gumdrop-like, retro, curvy, and stylish MA profile keycaps. Here is a 5 pack of Cyan MA Keycaps for your next mechanical keyboard or NeoKey project. Snap 'em onto any Cherry MX or compatible switch&...

SKU: AF-5175 · MPN: 5175

Dress up your mechanical keys in your favorite colors with a wide selection of gumdrop-like, retro, curvy, and stylish MA profile keycaps. Here is a 5 pack of Orange MA Keycaps for your next mechanical keyboard or NeoKey project. Snap 'em onto any Cherry MX or compatible switc...

SKU: AF-5173 · MPN: 5173

Dress up your mechanical keys in your favorite colors with a wide selection of gumdrop-like, retro, curvy, and stylish MA profile keycaps. Here is a 5 pack of Green MA Keycaps for your next mechanical keyboard or NeoKey project. Snap 'em onto any Cherry MX or compatible switch...

SKU: AF-5178 · MPN: 5178

Dress up your mechanical keys in your favorite colors with a wide selection of gumdrop-like, retro, curvy, and stylish MA profile keycaps. Here is a 5 pack of Pink MA Keycaps for your next mechanical keyboard or NeoKey project. Snap 'em onto any Cherry MX or compatible switch&...

SKU: AF-5172 · MPN: 5172

Dress up your mechanical keys in your favorite colors with a wide selection of gumdrop-like, retro, curvy, and stylish MA profile keycaps. Here is a 5 pack of Red MA Keycaps for your next mechanical keyboard or NeoKey project. Snap 'em onto any Cherry MX or compatible switch&n...

SKU: AF-5723

The Feather RP2040 with USB Type A Host adds a full USB Type A port to the Feather, letting you connect USB devices like keyboards, mice, flash drives, and serial peripherals. The USB host functionality is achieved through the RP2040's PIO peripheral, which emulates a USB host controller while ke...

SKU: SF-DEV-15123

The SparkFun RedBoard Qwiic is an Arduino-compatible development board in the UNO R3 form factor with a built-in Qwiic connector for solderless I2C hookup. It programs over USB Micro-B using the Arduino IDE — select "Arduino UNO" from the board menu and you're ready to go. Key improvements over ...