All Products

SKU: AF-3342

This 2×40 right-angle edge connector fits directly onto the bottom edge contacts of the BBC micro:bit, providing access to all GPIO pins, power, and ground connections. The right-angle design is ideal for mounting on custom PCBs. The connector has 80 pins total, but because the micro:bit edge co...

SKU: AF-5960 · MPN: ADA5960

The Adafruit CH552 QT Py is a compact development board built around the WCH CH552, an enhanced 8-bit 8051 microcontroller. Running at 16 MHz with native USB device support, it packs a surprising amount of functionality into the tiny QT Py form factor with STEMMA QT / Qwiic I2C connectivity. The...

SKU: EF-EF03435

An accessory pack for the ElecFreaks Ring:bit Car V2, adding obstacle avoidance, line-following, and colourful LED lighting to your micro:bit-powered car. The kit includes three modules that plug directly into the Ring:bit Car for expanded functionality. What's Included Sonar:bit (Ultrasonic S...

SKU: PR-PIM373

The VL53L1X Time of Flight sensor breakout uses a low-power laser to measure distances with excellent accuracy and speed. With a detection range of 4 cm to 4 metres and up to 50 Hz sampling frequency, it's ideal for proximity sensing, presence detection, and collision avoidance on robots. This b...

SKU: PL-1125

A compact, inexpensive brushed DC motor with a 120:1 plastic reduction gearbox, well suited for small robot builds. The motor is rated for 4.5V but runs comfortably in the 3–6V range. The gearbox output shaft is a 3mm D-shape, offset from and parallel to the motor shaft. A built-in safety clutch ...

SKU: PR-PIM082

Explorer HAT Pro adds a lot of useful tools to your Raspberry Pi.It has digital inputs and outputs, capacitive touch pads, croc. clip compatible pads, coloured LEDs, analog inputs, motor drivers, and a mini breadboard for prototyping your projectsGreat for little robots, games, science ...

SKU: KI-2746

When using through hole LEDs it can be hard to form the eyelets and then work out which leg is positive and negative. That's where these Sewable LED Holders come in! The 5mm LED holder boards, quickly and easily take any through hole 5mm LED and (after soldering in place) make them easy to use in...

SKU: EF-EF10138

The KittenBot Silicone Sleeve is a soft protective case for the BBC micro:bit, available in blue. The flexible silicone wraps around the board to guard against bumps, drops, and scratches while keeping all buttons, the LED matrix, and edge connector accessible. Key Features Soft Silicone Const...

SKU: EF-EF08180

ElecFreaks Micro:bit Starter Kit is designed for people who is at the door step of learning electric circuit and programming knowledge. The kit has provided some basic electronic components like LED, button, buzzer, temperature sensor , steering engine and motor etc.. You can not only learn basic...

SKU: LB-3000MAH

Stay charged anywhere with our compact 3000mAh Micro:bit Charger.Unlike many power banks that shut down with low power draw, this one stays on even when your Micro:bit uses minimal power.Includes a USB-C cable for charging the power bank. Use your Micro:bit USB-A to Mini-USB cable to power your M...

SKU: SF-WRL-13225

The SparkFun XBee Explorer Serial is an RS232 serial base unit for configuring and communicating with XBee modules. Compatible with all XBee modules including Series 1, Series 2.5, standard, and Pro versions. Simply plug in an XBee module, connect an RS232 cable, and gain direct access to the ser...

SKU: SF-ROB-10391

A linear push-type solenoid rated for 36 V DC that also works well at 12 V. Solenoids produce linear motion for pushing, pulling, or actuating switches and levers. This unit has a measured throw of approximately 10 mm. Key Features Linear Push Solenoid – For push, pull, and actuation applicati...

SKU: SF-DEV-12761

The SparkFun microSD Shield gives your Arduino mass-storage capability via a microSD card slot, making it ideal for data-logging and projects that need to read or write files. Communication with the microSD card uses the SPI interface. The SCK, DI, and DO pins connect to the ATmega168/328's stan...

SKU: AF-4011

An electronic snow globe kit that combines a Circuit Playground Express with a clear, durable plastic globe. Programme light and sound effects using MakeCode's drag-and-drop block editor — no soldering or coding experience required. Fill the globe with water, glitter, and glycerine for a working ...

SKU: DF-FIT0441

INTRODUCTION   This is a motor revolution: a new DC brushless motor with built-in motor driver. It can be conncected to Arduino directly without external motor driver. Whatsmore, the motor comes with directional control, PWM speed control and speed feedback output, which make this motor t...

SKU: EF-EF03423

The Ring:bit expansion board is a simple PCB for the micro:bit. The Ring:bit extends the micro:bit's 3 GPIO ports. We will use this module to convert the P0/P1/P2 port to the common GVS port. It can be loaded 3 AAA batteries to drive the car or other components.FeatureCompatble with LEGO holeEach...

SKU: LB-LS0823

The Micro: bit GPIO T-type Expansion Board is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pin. This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:...

SKU: ON-SERVOEXP

Add 16 independent PWM outputs to your Onion Omega2 for controlling servos, DC motors, and LED brightness. The onboard 3-pin connectors let you plug in standard servos directly – no breadboard or extra wiring needed. The built-in oscillator generates free-running PWM signals from 24Hz to 1526Hz....

SKU: SF-WRL-15435

The XBee3 Thing Plus is an ultra capable and easy way for getting into wireless device development. The combination of XBee and Qwiic in a space conscious design represents a much needed update to our XBee offering. With 20 I/O pins and Lithium Polymer Ion battery management, the XBee3 Thing Plus...

SKU: DF-DFR0123

This 20W adjustable DC-DC boost converter with a digital display is based on the professional boost chip and supports 3~32V power input, 5~35V output, and an accuracy of ±0.05V. The switching frequency is 400KHz, the conversion efficiency can reach 94%, it has the functions of overheating prote...