All Products

SKU: SF-COM-16273

A 16 mm deluxe thumb joystick similar to the analogue sticks found in PlayStation controllers. Two 10K potentiometers provide analogue position data for the full range of motion on both axes, and a built-in select button activates when the joystick is pressed down. The mechanical parts are mostl...

SKU: AF-4506

The Adafruit 1.3" Colour TFT Bonnet for Raspberry Pi combines a 240×240 IPS TFT display with a 5-way joystick and two pushbuttons on a single plug-and-play bonnet. The display is driven by the ST7789 controller over SPI, delivering vibrant 16-bit colour with wide viewing angles. A Qwiic/STEMMA Q...

SKU: AF-3464

The Adafruit Joy Bonnet turns your Raspberry Pi Zero into a handheld gaming device. This fully assembled bonnet sits on top of any Pi Zero and provides arcade-style controls — a mini joystick and buttons — that act as keyboard inputs once you run the Adafruit installer script. No soldering requir...

SKU: SF-COM-11275

It’s the end of the world, and you need a button to press. This is it. A 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a pre-installed long life horizontal microswitch. Button can also be adjusted to a low profile button by removing the midd...

SKU: PI-COM-B003

If you want to be a smooth operator then analog input is essential! This mini operators' joystick uses two 10KΩ potentiometers and a spring-back system for the X and Y axes making it a great input device for many robotics projects Connect one side of each potentiometer to ground, ...

SKU: AF-444

Add a tiny joystick to your project with this PSP thumbstick. This is a replacement component for PSP1000's, but we think they'd make for a great little joystick/thumbstick add-on for a wearable, or portable project. The joystick is a 'self-centering' analog-type. That means it basically a...

SKU: EF-EF03417

Joystick:bit V2 is a JoyStick based on micro:bit. It contains a 4-direction joystick and 4 undefined buttons as as classic JoyStick. At the same time, with the board buzzer and vibration motor, it also enhance game experience. Joystick:bit V2 can be remote control handle for micro:bit which on...

SKU: AF-1185

OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one c...

SKU: AF-1186

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can...

SKU: AF-1187

OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one ca...

SKU: AF-1191

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors.This button has a fl...

SKU: AF-1192

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors.This button has a fl...

SKU: AF-1193

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors.This button has a fl...

SKU: AF-1188

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one c...

SKU: AF-1190

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors.This button has a fl...

SKU: AF-1194

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors.This button has a fl...

SKU: AF-3103

Sometimes a simple analog control device can be the perfect tactile solution for your project, but they can be surprisingly hard to come by. Luckily we've found a low cost, quality PSP 3000 2-Axis Analog Thumb Joystick to fulfill your directional analog input needs! This is a replacement ...

SKU: PI-COM-B015

This clicky joystick is great for DIY arcade builds, and it has a handy 5-pin connector that means connecting it is just a case of plugging in a single cable connector. We use this joystick in our new Picade and it's solid, responsive, and reliable. The feel is a little looser tha...

SKU: SF-COM-09032

This is a joystick very similar to the ‘analog’ joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers - one for each axis. Pots are ~10k each. This joystick also has a select button that is actuated when the joystick is pressed down. Note: Breakout ...

SKU: AF-4697

A black rubber cap designed to fit standard 5-way navigation joysticks, providing a comfortable grip surface with directional etching. Presses on firmly and is easy to clean with mild soap and water. Compatible with common through-hole 5-way navigation switches used on boards such as TFT Feather...