All Products

SKU: DF-DFR0274

The RGB LED Strip Driver Shield allows you to control 12 V RGB LED strips (common anode) directly from an Arduino. With three PWM outputs capable of up to 3 A each, the shield can drive up to 10 metres of RGB LED strip. A built-in IR receiver enables remote control operation, and an on-board fuse...

SKU: DF-KIT0111

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible with Arduino UNO) along with 12 popular sensors and components from DFRobot's Gra...

SKU: AF-171

Make your own Arduino motor party with a motor shield and a fine assortment of motors! New! we've upgraded the shield to our new version 2, with more powerful drivers, and uses fewer pins to boot! Included in this add-on pack is: Adafruit Motor Shield v2 for Arduino 6 Volt DC hobby motor Smal...

SKU: AF-1272

The Adafruit Ultimate GPS Logger Shield combines the popular Ultimate GPS module with a MicroSD card slot, giving your Arduino a complete GPS datalogging solution. Built around the MTK3339 chipset, it tracks up to 22 satellites on 66 channels with -165 dBm sensitivity and delivers up to 10 positi...

SKU: AF-3152

The Adafruit 0.8" 8x16 LED Matrix FeatherWing Display Kit in red pairs two miniature 8x8 LED matrices with a FeatherWing driver board to create a 128-pixel display for any Feather microcontroller. Use it for scrolling text, bitmap graphics, emoticons, or simple animations. The onboard HT16K33 I2...

SKU: AF-1313

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart.Works great with our Wave shield or class D amplifier board.

SKU: AF-2542

The Adafruit FONA 808 combines 2G cellular connectivity with integrated GPS tracking in a compact 1.75 × 1.6-inch breakout. Built around the SIM808 module with an MT3337 GPS chipset, it provides voice calling, SMS, GPRS data, and GPS geolocation — all controlled over a single serial port via AT c...

SKU: AF-5879 · MPN: ADA5879

The Adafruit UPDI Friend is a compact USB serial programmer for ATtiny microcontrollers that use the UPDI (Unified Program and Debug Interface) protocol. Built around the CH340E USB serial converter with USB Type-C, it provides reliable cross-platform programming with switchable 3V or 5V power an...

SKU: AF-2680

OK you've signed up for Adafruit.io and you're ready to build something cool and Internet-connected. All you need is this starter kit which will get you going with lots of parts that go very well with our service and are the most common sensors and actuators you may want. Sense light, motion, ...

SKU: SF-PRT-11417

These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (2 8-pin, 1 10-pin and 1 6-pin), enough to connect a shield t...

SKU: AF-1891

Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value). We particularly like th...

SKU: AF-5791

The Adafruit STEMMA Piezo Driver Amp uses the PAM8904 switched-capacitor driver to amplify signals for piezo elements at up to 300 kHz. With bridge-tied load (BTL) output and up to 3× voltage multiplication, it can deliver approximately 13 Vpp — much louder than driving a piezo directly from a 3V...

SKU: AF-4064

The Adafruit Grand Central M4 Express is a powerful development board built around the Microchip ATSAMD51P20 — a 120 MHz Cortex M4 processor with hardware floating point, 1 MB Flash, and 256 KB RAM. In the familiar Arduino Mega form factor, it brings 70 GPIO pins, dual DACs, 15 analog inputs, 8 M...

SKU: DF-KIT0018

The DFRobot Gravity Intermediate Kit for Arduino takes you beyond the basics with a comprehensive set of sensors, modules, and an Arduino-compatible board. Starting with simple LED projects and progressing to more complex builds like a mini electronic drum kit, sound-activated LED, and digital di...

SKU: AF-2442

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. Good for making simple moving robots. Comes with five horns and attachment screw...

SKU: AF-1271

Drive large 1.2" tall 7-segment displays with ease using this HT16K33-based I2C backpack. The updated design includes a built-in 5V boost converter so you get bright, consistent LED segments even when running from 3.3V power — no separate 5V supply needed. STEMMA QT / Qwiic connectors provide plu...

SKU: AF-5937 · MPN: ADA5937

The Adafruit BNO055 + BMP280 BFF is a compact add-on board that gives any QT Py or Xiao board powerful 9-degree-of-freedom (9-DoF) motion sensing plus barometric pressure and altitude measurement. It mounts directly onto the back of your QT Py, creating a tiny but capable sensor package. The BNO...

SKU: AF-3657

The Adafruit ATSAMD09 Breakout with seesaw is a versatile I2C peripheral board built on the Adafruit seesaw framework. Seesaw is a near-universal converter that lets you add GPIO, ADC, PWM, and more to any I2C-capable microcontroller or single-board computer — all over a simple I2C connection. R...

SKU: LB-CTCSINGLE

A single replacement kit for the Crack the Code unit of work. If you're already running the Crack the Code program in your classroom and need to replace or add an individual unit, this kit contains everything needed for one student station. Package Contents 1× Little Bird Arduino R3 Board 1× US...

SKU: AF-6057 · MPN: ADA6057