All Products

SKU: AF-269

The MAX31855 Thermocouple Amplifier Breakout converts K-type thermocouple readings into digital data via SPI, handling cold-junction compensation automatically. It measures temperatures from −200°C to +1350°C in 0.25°C increments, making it suitable for a wide range of temperature monitoring appl...

SKU: SF-SEN-13266

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and...

SKU: DF-DFR0558

This Gravity I2C high-temperature sensor pairs a signal amplification module (MAX31855K) with a stainless steel sheathed K-type thermocouple probe for measuring temperatures up to 800 °C. The module converts the thermocouple's millivolt signal to a 14-bit digital reading over I²C, with cold-junct...

SKU: AF-987

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving...

SKU: AF-270

A Type-K thermocouple with fiberglass braid insulation, rated to 500°C — far beyond the ~200°C limit of standard vinyl-insulated thermocouples. The bare bead probe design is suited to measuring both air and surface temperatures in high-heat environments such as ovens, kilns, heaters, and industri...

SKU: AF-4718

The Adafruit SPI Non-Volatile FRAM Breakout provides 2 Mbit (256 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no page writes, no block erasing, and each byte can be written 10 trillion times wit...

SKU: SF-BOB-13878

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat’s nest of wires. The Load Sensor Combinator was created to combine the 12 wires foun...

SKU: DF-DFR0123

This 20W adjustable DC-DC boost converter with a digital display is based on the professional boost chip and supports 3~32V power input, 5~35V output, and an accuracy of ±0.05V. The switching frequency is 400KHz, the conversion efficiency can reach 94%, it has the functions of overheating prote...

SKU: AF-3648

The Adafruit PT1000 RTD Temperature Sensor Amplifier is a breakout board for the MAX31865 precision RTD-to-digital converter, configured for PT1000 platinum resistance temperature detectors. It reads 2-, 3-, or 4-wire PT1000 sensors over SPI, delivering laboratory-grade temperature accuracy and r...

SKU: DF-DFR0316

A 4-channel, 18-bit delta-sigma analogue-to-digital converter (ADC) module based on the Microchip MCP3424. This module adds high-accuracy analogue input capability to Raspberry Pi, Arduino, and other microcontroller platforms over I2C. The onboard programmable gain amplifier (PGA) allows the mod...

SKU: AF-1083

Add high-speed analog-to-digital conversion to any microcontroller with the ADS1015 breakout. This 12-bit ADC delivers 3,300 samples per second over I2C, with four single-ended or two differential input channels and a built-in programmable gain amplifier (up to 16×) for boosting small signals. T...

SKU: AF-1032

A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object is moving!) As these sensors become more popular and easier to manufacture, the...

SKU: AF-5807 · MPN: ADA5807

This breakout is built around the HUSB238 USB PD sink chip, making it easy to negotiate power from a USB Type-C Power Delivery source without soldering tiny resistors. It plugs into a USB-C cable and uses the CC lines to request a suitable PD voltage.You can configure it with solder jumpers for f...

SKU: AF-6309 · MPN: ADA6309

Add high-quality amplified I2S digital audio to your project with this TLV320DAC3100 breakout. It provides clean stereo audio for 16Ω headphones and/or mono speaker output for a 4Ω-8Ω speaker, making it handy for compact audio builds without a separate amplifier.The board takes BCLK, WSEL and DIN...

SKU: SF-PRT-13612

This Thermocouple Connector is perfect for bridging the gap between Type-K thermocouples with standard connectors with a PCB. This little connector is actually the exact part we recommend using with our SparkFun Thermocouple Breakout! Each connector can easily attach to a printed circuit board...

SKU: AF-5870 · MPN: ADA5870

This compact breakout adds a high-resolution, single-channel ADC to your I2C bus, making it a handy choice for precision differential measurements. It is built around the MCP3421, a simple and low-cost 18-bit ΔΣ converter with adjustable gain, a built-in precision reference voltage, and support f...

SKU: SF-SEN-10245

A single-point load cell (strain gauge) rated for up to 50 kg. This is the same type of sensor found in digital bathroom scales. It outputs a small analogue voltage proportional to the applied force, which can be read using a load cell amplifier such as the HX711. Specifications Capacity – 50 ...

SKU: DF-SEN0656 · MPN: SEN0656

The CT1780 is a cold-junction compensated amplifier for K-Type thermocouples, designed to make extreme temperature measurement easier to add to microcontroller projects. It digitises the tiny thermocouple signal and provides temperature readings with 0.25℃ resolution over a very wide measurement ...

SKU: SF-SEN-00251

36" high temperature Type-K Thermocouple with glass braid insulation.

SKU: AF-3245

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare wires stainless-steel tip probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200°C, this one uses a fiberglass braid so...