All Products
Collections
Showing 1-20 of 60 products
Sabertooth Dual 25A DC Motor Driver
The Sabertooth 2X25 is a versatile dual DC motor driver capable of supplying up to 25A continuous (50A peak) per channel. Suitable for high-powered robots up to 100lbs in combat or 300lbs for general-purpose robotics, it features synchronous regenerative drive that recharges batteries during brak...
Pololu Dual G2 High-Power Motor Driver 18v18 Shield for Arduino
The Pololu Dual G2 High-Power Motor Driver 18v18 Shield uses pairs of discrete MOSFET H-bridges to drive two large brushed DC motors. It has an Arduino shield form factor for direct plug-in use, and also breaks out all motor driver pins along the left side for standalone operation without an Ardu...
SparkFun IoT Brushless Motor Driver (ESP32 WROOM, TMC6300)
The SparkFun IoT Brushless Motor Driver is a powerful, easy-to-use motor driver that can control any 3-phase BLDC with built-in WiFi and Bluetooth® capabilities! However, with our on-board Three Phase Brushless Gimbal Motor, you can be sure of getting the best performance and reliability without ...
SparkFun Brushless Motor Driver - 3-Phase (TMC6300)
The SparkFun 3-Phase Brushless Motor Driver, featuring the TMC6300 from ADI + Trinamic, is a powerful and easy-to-use three-phase motor driver that was designed to control our Brushless Gimbal Motor. It can be used to control any 3-phase BLDC or PMSM motor with up to 2A (1.4ARMS) of total driv...
TMC260 Stepper Motor Driver Shield For Arduino
INTRODUCTION This is a stepper motor driver introduced by DFRobot for those projects require powerful stepper motors, such as a pair of automatic curtains, an XY Plotter. This shield allows Arduino drive stepper motors (up to 2A per motor coil, 40V max). This stepper mo...
Gravity: Haptic Motor Driver for LRA Motors
·
This Gravity haptic driver module is built for Linear Resonant Actuators (LRAs), turning simple I2C commands into crisp tactile feedback for interactive projects. It is powered by the TM6605 driver chip and supports LRA resonant frequencies from 140Hz to 220Hz.The module includes 44 built-in vibr...
PD Stepper NEMA 17 USB-C PD Driver and Controller
·
Stepper motor builds often need a microcontroller, a separate driver, a 12V or 24V supply and plenty of wiring. This compact controller from Things by Josh brings that stack together in one unit designed to mount directly to the back of a standard NEMA 17 stepper motor.Power comes in via USB-C Po...
Micro bit DRV8833 Motor Driver Expansion Board
The micro:bit DRV8833 Motor Driver Expansion Board adds dual DC motor control to the BBC micro:bit. Built around the DRV8833CPWP motor driver IC, it can output up to 700 mA per channel with four control modes: clockwise rotation, anticlockwise rotation, brake, and stop. The board includes on-boa...
2x3A DC Motor Driver Carrier Board for UNIHIKER M10
·
This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....
Dual-Channel DC Motor Driver-12A
This is a dual channel DC motor driver with an extremely small size of of 1.97”×1.97”×0.49”. The module comes with two motor channels that can drive two motors simultaneously, and each channel employs an indicator to show the rotation direction of the motor: blue is forward rotation, red is rever...
SimpleFOCmini Brushless DC Motor Driver Board
·
This compact DFRobot driver board is made for precise control of brushless DC motors using Field-Oriented Control (FOC). At just 26 x 21.5mm, it is well suited to tight builds where smooth motion, low noise and responsive control matter.SimpleFOCmini supports closed-loop control of motor position...
EasyDriver Stepper Motor
The EasyDriver is a simple stepper motor driver board based on the Allegro A3967 IC. It accepts a digital step/direction input (3.3 V or 5 V logic) and drives bi-polar stepper motors (4, 6, or 8 wire) at any voltage within the 7–30 V supply range. The board features adjustable current control fr...
SparkFun Motor Driver - Dual TB6612FNG (1A)
The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...
L9110H H-Bridge Motor Driver for DC Motors - 8 DIP - 2.5V-12V 800mAh
Run two solenoids, or a single DC motor with up to 800mA per channel using the super-simple L9110H H-bridge driver. This bridge chip is an 8 DIP package so it's easy to fit onto any breadboard or perfboard.Each chip contains one full H-bridges (two half H-bridges). That means you can drive 2 sole...
2x1.2A DC Motor Driver with Gravity Connector (TB6612FNG)
The DFRobot 2×1.2A DC Motor Driver with Gravity Connector is a compact dual-channel motor driver based on the TB6612FNG IC. This version features standard DFRobot Gravity connectors for plug-and-play wiring with Gravity-compatible expansion boards — no soldering or breadboard needed. Each channe...
2x7A DC Motor Driver
An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...
SparkFun Serial Controlled Motor Driver
The SparkFun Serial Controlled Motor Driver allows you to control up to two DC motors using a serial command interface. The serial interface is easy to use and it lets the user select an individual motor, the direction, and the desired speed constant (up to 10 different speed from stop to full sp...
Mosfetti 4 Channel MOSFET Driver Board by Monk Makes
The Mosfetti by Monk Makes is a compact 4-channel MOSFET switch designed for maker projects. Each channel can drive up to 2 A of low-side switching at up to 16 V DC, making it perfect for controlling relays, solenoids, LED strips, pumps, and motors from a microcontroller. Supplied as a PCB with ...
Adafruit STSPIN220 Stepper Motor Driver Breakout Board
·
The Adafruit STSPIN220 Stepper Motor Driver Breakout makes controlling bipolar stepper motors simple with a GPIO-only interface — just two pins (DIR and STEP) are all you need. It defaults to 1/16 microstepping and supports up to 1/256 microstepping via mode pin configuration, making it ideal for...
Dual H-Bridge Motor Driver for DC or Steppers - 600mA - L293D
Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers in our Adafruit Motorshield". If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it....
