All Products

SKU: SF-PRT-12614

Description: This is one giant solderless breadboard! It has 7 power buses, 40 columns, and 63 rows - with a total of 3220 tie in points. All pins are spaced by a standard 0.1". The two sets of five columns are separated by about 0.3", perfect for straddling a DIP package over. The board accepts ...

SKU: AF-4354

The Adafruit Perma-Proto 40-Pin Raspberry Pi Breadboard PCB Kit combines a full-sized prototyping board with a built-in Pi Cobbler breakout. Solder in the included 2×20 box header, connect a 40-pin GPIO cable, and you get labelled pin breakouts alongside 60 rows of breadboard-style prototyping sp...

SKU: AF-1148

The Adafruit Half-size Perma-Proto Raspberry Pi Breadboard PCB Kit combines a prototyping board with a built-in Pi Cobbler breakout. Solder the included 2×13 box header onto the board, connect a 26-pin GPIO ribbon cable (not included), and you get labelled GPIO breakouts alongside a generous half...

SKU: AF-239

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the breadboard as thin as 1.4" (3.5cm). You can also ...

SKU: SF-PRT-12699

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all...

SKU: LB-00103

A high-quality 840-point solderless breadboard with ABS housing and brass contact clips for reliable connections. The classic beige colour gives it a retro look while delivering solid performance for prototyping. Key Features 840 Tie Points – 640 terminal strip + 200 power distribution strip ...

SKU: SF-PRT-13157

The SparkFun Breadboard Power Supply Stick provides clean, regulated 3.3 V or 1.8 V power directly to your breadboard. It accepts 4–9 V input via a DC barrel jack or 2-pin header, and outputs regulated voltage through pins spaced to power both rails of a standard full-size breadboard simultaneous...

SKU: AF-3695

The Adafruit DragonTail for micro:bit breaks out all of the micro:bit's edge connector pads to standard 0.1" headers for easy breadboard use. Simply slot your micro:bit into the card-edge connector and every pin — including I2C, SPI, and analogue inputs — becomes accessible on a solderless breadb...

SKU: DF-FIT0908

This kit includes two kinds of mini multi-color block building breadboards and 2 base plates of different sizes. Users can freely assemble these breadboards to make various projects combining with other microcontrollers like Arduino, Raspberry Pi, etc., or use them in circuit assembly and test in...

SKU: DF-FIT0428

The ECell Breadboard-Plugin Connector is a reusable adapter that lets you plug common components neatly into a solderless breadboard. Gold-plated 0.64 mm pins perfectly match standard breadboard tie-points for reliable, durable connections without deforming pins or tie-points. Each connector is ...

SKU: DF-FIT0426

INTRODUCTION Introducing "The Breadboard-Plugin Kit" - the first kit in the ECell series. The Breadboard-Plugin Kit provides a range of common components such as resistors, capacitors, diodes, transistors etc. that are compatible with a solderless breadboard. This Di...

SKU: AF-1872

This 8 MHz ceramic resonator is a breadboard-friendly oscillator with built-in load capacitors, making it a simple drop-in timing source for microcontrollers. With 0.5% accuracy, it's well suited for everyday electronics, UART baud-rate generation, and general microcontroller clocking. The 3-pin...

SKU: DF-FIT0009

This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits. SPECIFICATIONS   Size:170*65mm (6.7x2.6 in) Suitable for 0.3-0.8 mm (0.01x0.03 in) wire SHIPPING LIST   Medium Bread Board Self Adh...

SKU: LB-BK-SPEAKER

A bulk pack of 20 breadboard-compatible speakers — a Little Bird exclusive. Each speaker comes with jumper wires and standard header pins pre-soldered, so it plugs directly into a breadboard with no extra wiring needed. Originally designed for talking greeting cards, these speakers are extremely...

SKU: AF-5422

It can be tricky to work out which pin is which when the Raspberry Pi Pico is attached to solderless breadboard. Luckily, the MonkMakes Breadboard for Pico solves this problem by labeling the Pico pins on the breadboard.This cute 3.2″ × 2.1″ (82 × 53mm) solderless half-size breadboard has four bu...

SKU: AF-1465

Stop searching for the AVR ISP pinout every time you program. This simple breakout adapter converts the standard 2×3 AVR ISP box header to two breadboard-friendly 1×3 rows, making it easy to wire up your programmer without crossed wires or guesswork. The adapter plugs neatly into any standard br...

SKU: AF-1699

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 0.1" spacing so it plugs very soli...

SKU: SF-PRT-12702

This is the Mini SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the same connections to pins. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces i...

SKU: SS-106990021

The 5V/3.3V Breadboard Power Supply plugs directly into a standard breadboard and provides regulated 5V or 3.3V power to both rails. It accepts power via either a 7–15V DC barrel jack or a 5V Micro-USB input, giving you flexible options for powering your prototyping projects. Designed by Seeed S...

SKU: DF-MBT0009

Micro:breadboard is a micro:bit-based expansion board specially designed for STEM-starter. It comes with a 3.23*2.17” breadboard (independent packing, you need to stick them together), on which you can directly build circuit with all sorts of electronic components. All IO ports are led out in ...