All Products

SKU: AF-4020

Everything you need to get started with the NeoTrellis M4 in one kit. This pack bundles the NeoTrellis M4 Mainboard, an acrylic enclosure, silicone elastomer button pads, and rubber feet — ready to assemble into a complete MIDI controller, sound board, or interactive button-pad device. The NeoTr...

SKU: AF-4352

Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...

SKU: AF-4339

This laser-cut acrylic enclosure kit turns your 4×4 NeoTrellis setup into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside the NeoTrellis RGB Driver PCB. The enclosure inclu...

SKU: AF-4372

This laser-cut acrylic enclosure kit turns your 8×8 NeoTrellis setup (four 4×4 NeoTrellis boards) into a handheld device with an elegant black and white design and beautifully diffused button illumination. Designed to house any Adafruit Feather board (except FONA) alongside four NeoTrellis RGB Dr...

SKU: AF-3938

The NeoTrellis M4 Mainboard combines an ATSAMD51 Cortex M4 processor, a 4×8 grid of NeoPixel-lit elastomer button pads, stereo audio output, microphone input, and a triple-axis accelerometer into one compact, programmable board. Think of it as a button-mashing, light-flashing, tune-making powerho...

SKU: AF-3954

Upgrade your button-pad projects with full-colour NeoPixel backlighting. The NeoTrellis RGB Driver PCB is a 4×4 keypad controller with 16 NeoPixels and an onboard seesaw I2C chip that handles both button scanning and LED driving — all over plain I2C, no NeoPixel pin management required. The boar...

SKU: AF-1929

Build your own open-source 8×8 button grid controller with the Adafruit UNTZtrument kit. Designed by PaintYourDragon and based on the Adafruit Trellis platform, this DIY kit features 64 translucent silicone buttons with diffused white LEDs, housed in a custom laser-cut acrylic enclosure. Powered...

SKU: AF-6433 · MPN: ADA6433

Keep your Adafruit MagTag safe and looking sharp with this custom-designed 3D-printed enclosure. The snap-together two-piece case accommodates all connection ports and features flexible push tabs for the four front buttons, plus an integrated kickstand for tabletop use. Made with an SLA printing...

SKU: AF-1110

The Adafruit RGB Negative 16×2 LCD + Keypad Kit is a Pi Plate that combines a 16×2 character LCD with RGB backlight and a 5-button keypad, all controlled over I2C using just two pins. The negative-style display shows light text on a coloured background, giving a crisp, high-contrast appearance. ...

SKU: AF-4506

The Adafruit 1.3" Colour TFT Bonnet for Raspberry Pi combines a 240×240 IPS TFT display with a 5-way joystick and two pushbuttons on a single plug-and-play bonnet. The display is driven by the ST7789 controller over SPI, delivering vibrant 16-bit colour with wide viewing angles. A Qwiic/STEMMA Q...

SKU: AF-1490

These 6 mm tall tactile switch buttons are momentary normally-open pushbuttons commonly used as input buttons in electronics projects. The extra height makes them useful for projects in enclosures where the buttons need to protrude through the case. They work best when soldered into a PCB but ca...

SKU: AF-4675

A clear acrylic enclosure designed specifically for the Adafruit CLUE board. Laser-cut to accommodate the TFT display, tactile buttons, and capacitive pads, this minimalist case protects your board while keeping all features accessible. Assembly takes less than five minutes with the included nyl...

SKU: AF-802

The Adafruit 1.8" Colour TFT Shield is a plug-and-play display solution for Arduino, combining a bright 128×160 pixel TFT screen with a microSD card slot, 5-way joystick navigation switch, and three tactile buttons. This R3-format shield works with any Arduino or Metro board including the Metro M...

SKU: AF-1616

The Adafruit Trellis is an open-source backlight keypad driver system designed to work with the Adafruit 4×4 elastomer keypad and 3mm LEDs. Each tile handles keypress detection and LED control for a 4×4 grid over I2C, and up to 8 tiles can be connected together for a total of 128 buttons and LEDs...

SKU: AF-4028

Get started with CircuitPython using this all-in-one starter kit built around the Adafruit ItsyBitsy M4 Express. The ItsyBitsy M4 packs a 120 MHz ATSAMD51 Cortex M4 processor with floating point support, 512 KB flash, and 192 KB RAM into a compact, breadboard-friendly form factor — more than enou...

SKU: AF-4277

Everything you need to build a pocket-sized gaming handheld — no soldering required. This starter kit bundles the Adafruit PyGamer with a rechargeable battery, acrylic enclosure, speaker, button caps, and a zipper carry case. The PyGamer is powered by the ATSAMD51 (120 MHz ARM Cortex-M4) with 51...

SKU: AF-3915

Keep your Circuit Playground Express safe in this snap-together acrylic enclosure. Designed by Ada-friend Mike Doell, this minimal but elegant case turns your board into an electronic snowflake shape with no tools required for assembly. The enclosure provides full access to all buttons, the slid...

SKU: AF-6241 · MPN: ADA6241

A custom-designed snap-on enclosure for the Adafruit Feather RP2040 with DVI Output Port. 3D printed using an SLA process in translucent milky white plastic, it provides a clean, protective case with no visible layer lines or surface imperfections. No screws or glue required — simply snap the Fe...

SKU: AF-3963

So you've got your Adafruit NeoTrellis M4, a cool/witty name for your band, a Soundcloud account, a 3D-printed Daft Punk helmet... so what could be missing from your road to stardom?...The NeoTrellis M4 Enclosure, of course! A super-specifically laser-cut enclosure that turns your 'Trellis into a...

SKU: AF-2866

Put on your sunglasses before plugging in this shield — 40 eye-blistering RGBW LEDs adorn the NeoPixel Shield for a blast of configurable colour and white. Arranged in a 5×8 matrix, each pixel is individually addressable using just one pin (Digital #6 by default, changeable by cutting a trace). ...