All Products

SKU: AF-2396

This 7" HDMI display with resistive touchscreen delivers 1024×600 resolution in a compact form factor ideal for Raspberry Pi, BeagleBone Black, and other single-board computers. The included mini driver board is powered via USB and accepts HDMI input for high-quality video output. The kit also i...

SKU: AF-628

A complete starter pack for getting into electroluminescent (EL) panels. Includes a 10 × 10 cm white EL panel, a portable battery-powered inverter, and AAA batteries — everything you need to start glowing right out of the box. The 4×AAA inverter drives a single panel and provides approximately 1...

SKU: AF-4028

Get started with CircuitPython using this all-in-one starter kit built around the Adafruit ItsyBitsy M4 Express. The ItsyBitsy M4 packs a 120 MHz ATSAMD51 Cortex M4 processor with floating point support, 512 KB flash, and 192 KB RAM into a compact, breadboard-friendly form factor — more than enou...

SKU: AF-2395

A 7-inch touchscreen display with 1024×600 resolution and a resistive touchscreen overlay, ideal for Raspberry Pi projects, embedded computing, and multimedia setups. The included driver board supports HDMI, VGA, and composite (NTSC/PAL) inputs, making it compatible with a wide range of devices. ...

SKU: AF-632

A complete starter pack for electroluminescent (EL) tape projects, including a 1 m aqua EL tape strip, a portable battery-powered inverter, and batteries. Everything needed to get started with EL lighting right out of the box — no additional components required. Key Features Complete Kit – EL ...

SKU: AF-627

A complete starter pack for your first electroluminescent (EL) panel project. Includes a 10 × 10 cm aqua EL panel, a portable battery-powered inverter, and batteries — everything needed to get glowing straight out of the box. The 4×AAA inverter is powerful enough to drive the included panel for ...

SKU: AF-2218

The TFP401 breakout is a compact HDMI/DVI decoder that outputs raw 24-bit colour pixel data to 40-pin TTL displays. It decodes unencrypted video at any resolution from 25–165 MHz pixel clock (up to 1080p) and includes a built-in backlight driver with PWM dimming control. Designed for use with si...

SKU: AF-2680

OK you've signed up for Adafruit.io and you're ready to build something cool and Internet-connected. All you need is this starter kit which will get you going with lots of parts that go very well with our service and are the most common sensors and actuators you may want. Sense light, motion, ...

SKU: AF-1934

This 7" TFT display delivers 800×480 resolution with an extra-bright backlight and a versatile driver board that accepts HDMI, VGA, and composite (NTSC/PAL) video inputs. Simply connect a 5–12V DC power adapter and plug in your video source — the driver auto-detects the active input and displays ...

SKU: AF-584

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Green. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or recharge...

SKU: AF-2076

These 2×23 male headers plug directly into the side sockets on the BeagleBone Black, allowing you to attach prototype PCBs or capes. Each pack includes two headers — one for each side of the BeagleBone Black. Key Features 2×23 Pin Layout – Matches the BeagleBone Black expansion headers 2.54 m...

SKU: AF-2562

Everything you need to get started with NeoPixel LED strips in one convenient pack. Includes a 1-metre NeoPixel strip with black flex PCB, power supply, and connectors — just add a microcontroller and you're ready to go. With minimal or no soldering required, this starter pack is the fastest way...

SKU: AF-586

A little bundle to get you started! This project pack contains: 2.5 meters (over 8 ft) of high-brightness, long-life EL wire in Orange. 2.5 meters is the maximum amount for the pocket driver - it is cut and soldered so it's ready to go! Pocket EL inverter runs on 2 AA Alkaline or recharg...

SKU: AF-633

Get glowing in seconds with our Electroluminescent (EL) Tape Starter Pack! This pack contains everything you need for your first EL tape project, even the batteries. Includes: 1 meter long x 1 cm wide EL tape strip in Blue Portable 4xAAA inverter powerful enough to drive a full meter of s...

SKU: AF-4352

Build a handheld light-up button controller with this complete kit that pairs the Adafruit 4×4 NeoTrellis RGB Driver with a Feather M4 Express inside an elegant laser-cut acrylic enclosure. The 16 silicone buttons each have individually addressable NeoPixels underneath, and the seesaw I2C chip ha...

SKU: AF-1737

A compact wireless QWERTY keyboard with a USB dongle, ideal for pairing with a Raspberry Pi, BeagleBone, or any computer with a USB port. The slim chiclet-style keys provide a comfortable typing experience in a small footprint. The wireless USB dongle is plug-and-play — it shows up as a standard...

SKU: AF-6020 · MPN: ADA6020

DescriptionElevate your Bus Pirate 5 experience with this premium accessory. This keyed and locking probe cable, crafted from soft and flexible silicone-coated wire, connects seamlessly to the Bus Pirate's 10-pin main header. The 2.54mm Dupont connectors at each end are compatible with a variety...

SKU: AF-4197

Add a crisp, paper-like display to your microcontroller project with the Adafruit 2.13" Monochrome eInk Breakout. This 250×122 pixel black-and-white eInk panel delivers excellent daylight readability and retains its image even with power completely disconnected — just like printed paper. An onbo...

SKU: AF-4204

A mixed pack of 25 diffused 10 mm LEDs in five colours — white, blue, green, yellow, and red (5 of each). The large diffused lens provides wide-angle visibility and even light output, making these LEDs easy to see in daylight and from any direction. Breadboard-compatible with standard through-ho...

SKU: AF-2561

Everything you need to get started with NeoPixel LED strips in one convenient pack. Includes a 1-metre NeoPixel strip with white flex PCB, power supply, and connectors — just add a microcontroller and you're ready to go. Also available with a black flex PCB. With minimal or no soldering required...