All Products

SKU: PL-1155

A compact enclosed battery holder for six AA batteries, providing approximately 9V (alkaline) or 7.2V (NiMH rechargeable) from a series configuration. Features bare wire leads for flexible integration into your project. Key Features 6-Cell Capacity – Holds six AA batteries in series Enclosed ...

SKU: PL-1161

A battery holder for eight AA cells, arranged as two back-to-back four-cell holders. Provides up to 12V (with alkaline cells) in a compact, stackable form factor. Specifications Cell Type – AA Capacity – 8 cells Configuration – Two 4-cell holders, back-to-back Output – Up to 12V (series, al...

SKU: PL-1166

These 0.1 μF 100 V ceramic capacitors have many uses, including noise suppression on motors.

SKU: PL-2173

A male Tamiya-style high-current connector with two pre-crimped 10cm 14-AWG silicone-insulated leads. This keyed connector is commonly used with 7.2V RC battery packs and features a latch to prevent accidental disconnection. The leads extend 9cm past the housing with stripped, tinned terminations...

SKU: PL-2265

This tiny DC motor has a shaft with an offset mass that vibrates when it rotates. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback. The motor has 1.5″ leads and is encased in a removable rubber sleeve that gives it flat surfaces for m...

SKU: PL-2267

A NEMA 17 hybrid bipolar stepper motor with a 1.8° step angle (200 steps per revolution). Each phase draws 1.7 A at 2.8 V, delivering a holding torque of 3.7 kg·cm. Four colour-coded wires with bare leads connect to two coils: black/green for one coil, red/blue for the other. Best driven with a ...

SKU: PL-1402

This single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch or tactile bump sensor for your robot. The switch body dimension is 20.0 x 6.4 x 10.2 mm, and the lever arm is 16.7 mm long.

SKU: PL-1403

This single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch, but the long lever arm makes it especially useful as a tactile bump sensor for your robot (e.g whiskers or antennae). The switch body dimension is 20.0 x 6.4 x 10.2 mm, ...

SKU: PL-1406

This single-pole, double-throw (SPDT) rocker switch makes a great on/off power switch. It is rated for 10 A at 125 VAC and 6 A at 250 VAC.

SKU: PL-1490

A compact 170-point solderless breadboard in classic white, perfect for small circuits and prototyping with DIP ICs. The 17-row layout accommodates up to two 14- or 16-pin DIP packages, making it ideal for quick test circuits and portable projects. Interlocking tabs on the sides allow multiple b...

SKU: PL-2441

These side-entry screw terminal blocks have a pitch of 5 mm (0.197″). Each block has three terminals for the stripped ends of 22 – 14 AWG wires, and units can slide together to make longer strips. They are rated for 250 V, 16 A (UL) and ship in packs of four.

SKU: PL-2440

A pack of four 2-pin screw terminal blocks with 5 mm pitch and side-entry wire orientation. Simply tighten or loosen the screws to connect or release wires — no soldering needed for the wire connection itself. Each block features a ridge on one side and a slot on the other, allowing multiple blo...

SKU: PL-2449

This connector adapts a 5.5 × 2.1 mm DC barrel jack to a pair of screw terminals spaced approximately 5 mm (0.2″) apart. The terminals are labeled positive and negative, with the positive terminal connected to the center pin.

SKU: PL-2463

The Vishay TSSP58P38 is a unique modulated IR receiver that is designed for IR brightness detection instead of data communication for remote control. This sensor can be used with a 38 kHz modulated IR emitter and the appropriate algorithms to form a distance sensor with a range of up to a f...

SKU: PL-2458

The QTR-1A reflectance sensor carries a single infrared LED and phototransistor pair in an inexpensive, tiny 0.5" x 0.3" module that can be mounted almost anywhere and is great for edge detection and line following. The reflectance measurement is output as an analog voltage. This sens...

SKU: PL-1576

A high-power 6V brushed DC gearmotor with a 98.78:1 metal spur gearbox. The cylindrical motor body measures just under 25mm in diameter, and the D-shaped output shaft is 4mm in diameter, extending 12.5mm from the gearbox face plate. Also available with an integrated encoder for closed-loop contro...

SKU: PL-1587

A low-power 6V brushed DC gearmotor with a 98.78:1 metal spur gearbox. The cylindrical motor body measures just under 25mm in diameter, and the D-shaped output shaft is 4mm in diameter, extending 12.5mm from the gearbox face plate. The low-power variant draws less current than the HP version, mak...

SKU: PL-2510

Overview A Zumo robot preparing to attack a Parallax SumoBot. Zumo Robot for Arduino, v1.2. This Zumo robot is a low-profile tracked robot platform intended for use with an Arduino (or compatible device, such as an A-Star 32U4 Prime) as its main controller. It measures less than 10 ...

SKU: PL-1636

This tiny, button-type, vibrating motor shakes with a vibration amplitude of 0.75g and draws approximately 60 mA when 3 V is applied to its leads. The shaftless design keeps this motor small: 10 mm in diameter and 3.4 mm in height.

SKU: PL-2669

This triple-row, 120-pin (3×40) right-angle male header strip with 0.1" (2.54mm) pitch is a versatile connector for electronics projects. The breakaway design lets you snap or cut it into any triple-row length you need, and the right-angle orientation is ideal for low-profile connections where ve...