All Products

SKU: M5-U051

Including 7 Different Units: Ext.IO, Proto, Relay, 3.96, RS485, DAC, ADC  

SKU: DF-SEN0598

An IP68-rated ultrasonic obstacle avoidance sensor specifically designed for underwater applications. With a measurement range of 2–300cm and UART output, this compact sensor enables underwater vehicles and robots to detect obstacles without relying on cameras. Operating on a wide 5–24V voltage ...

SKU: DF-SEN0599 · MPN: SEN0599

An underwater ultrasonic obstacle avoidance sensor designed specifically for submerged applications. With an IP68 protection rating and a measurement range of 5–600 cm, it enables underwater vehicles to detect and avoid obstacles without relying on cameras or human observation. Operating on a wi...

SKU: DF-FIT0957 · MPN: FIT0957

The IPEX4 to SMA Female Connector Cable is a 200 mm adapter designed for single-board computers equipped with an IPEX4 (MHF4) wireless interface, including the LattePanda 3 Delta, LattePanda 2 Alpha, and LattePanda 2 Delta. It converts the onboard IPEX4 connector to a standard SMA female port (ex...

SKU: DF-FIT0833

This gold-plated IPEX to SMA female connector has passed 48 hours salt spray test, which is durable and not easy to rust.It adopts RG1.13 wire material and high-density shielding layer, soft and firm, fold-resistant and durable, with fast and stable data transmission.These IPEX to SMA Female Cabl...

SKU: DF-FIT0872

A gold-plated IPEX (U.FL) to SMA male (inner needle) pigtail cable for connecting wireless modules to external antennas. The gold-plated connectors have passed 48-hour salt spray testing for long-lasting corrosion resistance. Built with RG1.13 wire and a high-density shielding layer, this cable ...

SKU: AF-2167

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to ...

SKU: DF-SEN0503

An infrared break-beam sensor pair for simple, reliable motion detection. The emitter sends a beam of invisible IR light to the receiver — when an object passes between them and breaks the beam, the receiver outputs a signal. Works up to 50 cm at 5 V with a fast response time under 2 ms. The com...

SKU: AF-2168

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to IR,...

SKU: AF-164

The Sharp GP2Y0A21YK0F is an infrared distance sensor that measures distances from 10 cm to 80 cm by bouncing IR light off objects. It outputs an analogue voltage proportional to distance — approximately 3 V at 10 cm and 0.4 V at 80 cm — which can be read directly by an Arduino or other microcont...

SKU: AF-1031

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 8" long 3-JST interface wire. These sensors are good for detection between 20cm-150cm. For over 1 m distance...

SKU: PI-LNG001

An open source, programmable, Arduino-compatible USB infrared receiver that gives new life to old remote controls. IRduino is a peripheral device that allows almost any IR signal to be translated into commands. It works on many platforms, including PC, Mac, Raspberry Pi, and even some cell pho...

SKU: SF-COM-29198 · MPN: COM-29198

The IRF7509 is a common N- and P-channel MOSFET device for switching higher-power loads from low-power control signals. Its low on-resistance helps reduce losses, while the logic-level gate is suited to control from many 5V microcontrollers or mechanical switches.This surface-mount MOSFET is usef...

SKU: LB-FLAME-LIGHT

This IR flame sensor module detects flames and infrared light sources in the 760–1,100 nm wavelength range. With a detection angle of approximately 60° and a test range of up to 80 cm (depending on flame size), it provides both digital and analogue output for flexible integration with Arduino, Ra...

SKU: SF-GPS-16838

The M1600HCT-P-SMA is a dual-band passive antenna that combines Iridium satellite communication with L1 GNSS reception (GPS and GLONASS) in a single compact unit. Ideal for tracking devices that transmit their position over the Iridium network. Weighing just 11 grams with a built-in O-ring, the ...

SKU: LB-LR0062

This IR sensor can detect obstacles in front of it.  When an object is detected the green indicator light on the board will light up. There is a low-level output signal on the OUT port.It has a detection range of 2-30 cm at an angle up to 35 degrees.The detection distance can be changed by u...

SKU: AF-157

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just pass...

SKU: DF-DFR0107

This IR kit provides a remote control capability to your project. DOCUMENTS   Wiki Arduino Library (Compatible with Leonardo) SHIPPING LIST   IR Remote Controller (With battery CR2025 inside) x1 IR Receiver Module x1 (SKU: DFR0094) Digital Cable x1

SKU: LB-00061

OverviewDeveloped as a quick starter board for the less experienced we envision this board as the follow up to your first soldering session.In isolation this board will produce a middle C note by hovering over the board. When combined with up seven additional boards a small piano can be formed, w...

SKU: SF-SEN-10266

Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP382 is a miniaturized receiver for infrared remote control systems. A PIN d...