All Products
Showing 21-40 of 100 products
Hobby Knife
It’s like an Xacto knife, only better. We use these extensively when working with PCBs. These small knives work well for cutting traces, scraping ground pours, and guiding hair-like wires into their proper place. Excel knife comes with aluminum handle, one ultra-sharp blade, and safety cap.
Missile Switch Cover - Red
It’s not what project you have in mind that may use a rocket launch switch… The question is what project will you come up with once you have one in hand? Everyone has a proverbial missile to launch.The hot red safety cover protects a toggle switch from accidentally being turned on. When flipped u...
Solder Wick #2 5ft. - Generic
Solder wick (also known as desolder braid) is made from braided copper threads treated with flux. When placed over an unwanted solder joint and heated with a soldering iron, the flux activates and draws the molten solder up into the braid by capillary action — cleanly removing solder from pads, b...
Relay Control PCB
A bare PCB for building a relay control circuit, based on SparkFun's Controllable Power Outlet tutorial. It allows you to switch high-voltage loads using a simple 0–5V GPIO signal from any microcontroller. Components must be sourced and soldered separately. Key Features Bare PCB – Solder your ...
LIDAR-Lite v3HP
The LIDAR-Lite v3HP is a compact, high-performance optical distance measurement sensor from Garmin. Housed in a durable IPX7-rated enclosure, it delivers accurate range measurements from 5 cm to 40 m, making it an ideal solution for drones, robots, and unmanned vehicles. Compared to the LIDAR-Li...
Hydrogen Sulfide Gas Sensor - MQ-136
The MQ-136 is a Hydrogen Sulfide detection sensor with a sensing range of 1 - 200ppm. The sensing element is SnO2, which has lower conductivity in clean air. When H₂S gas exists, the sensor’s conductivity gets higher along with the gas concentration rising. A simple circuit makes measuring this c...
Smoke Sensor - MQ-2
The MQ-2 is a smoke and combustible gas sensor manufactured by Winsen. It detects flammable gases and smoke in a concentration range of 300–10,000 ppm, with particularly high sensitivity to propane and smoke. It's widely used in domestic gas leakage alarms and portable gas detectors. The sensing...
Nicla Voice
The 22.86 x 22.86mm Nicla Voice allows for easy implementation of always-on speech recognition on the edge, because it integrates Syntiant’s powerful NDP120 Neural Decision processor to run multiple AI algorithms, leveraging bio-inspired, advanced machine learning to automate complex tasks. Ni...
Portability Shield for SparkFun Development Boards
·
Add the user interface and power features needed to take a compatible SparkFun development board into the field. This shield brings together battery power, charging, storage and controls in a compact add-on board.Power is handled with a LiPo battery connector, charger, fuel gauge and an on/off sw...
SparkFun Qwiic Pro Micro - USB-C (ATmega32U4)
This compact Arduino-compatible microcontroller board updates the classic Pro Micro format with handy modern additions while keeping the same overall footprint. It uses the ATmega32U4, giving you full USB functionality in a small board that can fit into tight builds.The board breaks out the famil...
SparkFun BlueSMiRF v2
·
This board creates a wireless Bluetooth® serial UART link, making it a handy replacement for short serial cables. Pair it, connect it, and pass serial data between TX/RX lines, with serial streams supported from 2400 to 921600 baud.BlueSMiRF v2 keeps the familiar 6-pin serial layout used by many ...
SparkFun Inventor's Kit - v4.1.2
A note for SparkFun Inventor's Kit v4.1 users: The only change that was made from the SIK v4.1 to the SIK v4.1.2 is our new carrying case. All of the internal parts and instructional guide have remained the same! The SparkFun Inventor's Kit (SIK) is a great way to get started with programmi...
INA228 Qwiic Current Sensor Breakout
·
This compact Qwiic breakout uses the Texas Instruments INA228 digital power monitor to measure DC current and power with high precision over I2C. The onboard 20-bit delta-sigma ADC supports readings for current, voltage, power, temperature, energy and charge accumulation.For quick wiring, the boa...
INA237 Qwiic Current Sensor
·
Monitor DC current and power over I2C with this Qwiic breakout based on the Texas Instruments INA237 digital power monitor. It measures current, bus voltage, internal temperature and power for an in-line DC input using a 16-bit delta-sigma ADC.The board is set up for flexible wiring: use the pair...
DE2290D 2D Barcode Scanner Breakout v2
·
Built around DYscan's DE2290D module, this SparkFun breakout brings 1D and 2D barcode scanning to USB and embedded projects. It uses CMOS image recognition with a 300,000-pixel global shutter camera, giving it the ability to read printed labels, merchandise packaging and codes displayed on screen...
RTK Kit Carrying Case
·
Keep your high-precision GNSS gear organised and better protected in the field with this RTK kit carrying case. It is designed for transporting an RTK receiver and key accessories between survey, mapping, robotics, and positioning jobs.The interior has custom moulded slots for an RTK receiver, a ...
RTK Facet Kit Carrying Case
·
Keep your high-precision GNSS gear organised and better protected when you are working out in the field. This carrying case is designed for the RTK Facet kit and provides dedicated storage for the main receiver and common accessories.Custom moulded slots inside the case are shaped for the RTK Fac...
XRP Robotics Platform Kit - Set of 10
·
This set of 10 XRP kits is designed for classrooms, robotics clubs and teams that need multiple hands-on robots for learning, coding and experimentation. The platform supports beginner through advanced activities, helping students build skills in science, engineering and problem-solving.Each kit ...
XRP Build-Your-Own Robotics Kit Parts - 30 Pack
·
The Experiential Robotics Platform (XRP) is a hands-on robotics platform designed for learning, prototyping and classroom projects. This build-your-own 30 pack supplies the hardware pillar of the XRP ecosystem, helping students build and program robots from beginner tasks through to more advanced...
JST Right-Angle SMD Connector - 2 Pin, Black
·
This compact two-pin connector is designed for surface-mount PCB layouts where you need a low-profile, right-angle connection. Its small footprint makes it well suited to tight electronics builds and embedded projects.The connector has a solid locking feel and is noted for its high current rating...
