All Products
Showing 21-40 of 100 products
JST SH Horizontal 6-Pin Connector - SMD
Here is a six pin horizontal 1.0mm pitch connector. It is useful if you need something very tiny as a connection. These are not the standard JST type connectors we use on most of our boards, but are actually the much smaller JST-SH type. Check the drawing below. Documents: Drawing
JST RCY Connector - Male/Female Set (2-pin)
This is a 2-pin JST RCY connector typically used for low-voltage applications running 10A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins to connect them both. The pins crimp to your cable and are inserted into the housing. 1 male so...
PIR Motion Sensor (JST)
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.This unit works great from 5 to 12V (datasheet shows 12V). You can also install a jumper wire past the 5V re...
Jumper Wire - JST Black Red
This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opposite end. Dimensions: 130mm length Documents: JST connector
JST SH Jumper 6 Wire - 1 Foot
This is a 1 foot long JST SH communication cable which can be cut and hacked to your needs. Ideal if you have a UAV project where the GPS module may be a distance away from the controller board. Cable has two 6-pin JST connectors with 1mm pitch. Wired pin 1 to pin 1.
2.5 mm JST XH-Style Shrouded Male Connector: 2-Pin, Straight (4-Pack)
A pack of four 2-pin shrouded male connectors in the JST XH style with 2.5mm pin spacing. These through-hole connectors mate with female JST XH-style cables and housings, providing a secure, polarised connection for power, battery, and signal wiring. The 2.5mm pitch is close enough to the standa...
micro:bit Battery Holder - 2xAAA (JST-PH)
This two-cell AAA battery holder is made for powering BBC micro:bit projects without needing to stay tethered to USB.The attached 6" (~150mm) lead is terminated with a JST-PH connector that mates with the JST socket on the micro:bit, making it simple to add portable power to your build.Note: JST ...
JST PH 4-Pin Socket to Color Coded Cable - 200mm
·
This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND Red for V+ White for SDA Green for SCL Even though...
2xAAA Battery Cage with JST Connector
A compact 2×AAA battery cage with a JST PH connector and 145 mm colour-coded leads. Designed to plug directly into the BBC micro:bit's battery socket, providing a portable power source for classroom projects and wearable builds. Key Features JST PH Connector – Plugs directly into the micro:bit...
JST PH 3-Pin to Female Socket Cable - 200mm
·
This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a ver...
JST PH 4-Pin to Female Socket Cable - I2C STEMMA Cable - 200mm
·
This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA bre...
2 x AAA Open Battery Holder with JST PH Connector
·
A slim, open-top 2×AAA battery holder with a genuine JST PH connector. Two AAA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and boards with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-Ion/LiPo...
JST SH 4-Pin to Premium Male Headers Cable - Qwiic Compatible - 150mm Long
·
This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remo...
2 x AA Open Battery Holder with JST PH Connector
·
A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...
JST SH 4-pin Right Angle Connector (10-pack) - Qwiic Compatible
·
A 10-pack of JST SH 4-pin right-angle connectors with 1 mm pitch through-hole mounting tabs. These are the standard connectors used with the Qwiic and STEMMA QT ecosystems, making it easy to add I2C connectivity to your own PCB designs. The solid plastic housing accepts standard Qwiic cables, an...
JST SH 9-Pin Cable - 100mm long
·
This 9-pin cable is just about 100mm / 4" long and fitted with JST-SH female connectors on both ends. Compared with chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel and are easy to insert and remove.We got these especially for our fantastically spooky Adafru...
Micro Servo with 3-pin JST Cable - STEMMA Connector Compatible
·
This tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor c...
Qwiic JST Connector - SMD 4-Pin (Vertical)
A surface-mount 4-pin JST connector in a vertical orientation, designed for the SparkFun Qwiic I2C ecosystem. This 1 mm pitch connector is used on all Qwiic-compatible boards and lets you build your own I2C devices that integrate seamlessly with the Qwiic system. The vertical mount profile is id...
2.5mm Pitch 5-pin Cable Matching Pair - JST XH compatible
·
A matching pair of 5-pin JST XH-compatible cables — one with an inline plug and one with an inline socket — for easy connect-and-disconnect wiring. The 2.5mm pitch connectors friction-lock together for a secure, reliable connection that's easy to separate when needed. Each cable is 20cm long wit...
2.5mm Pitch 6-pin Cable Matching Pair - JST XH compatible
·
A matching pair of 6-pin JST XH-compatible cables — one with an inline plug and one with an inline socket — for easy connect-and-disconnect wiring. The 2.5mm pitch connectors friction-lock together for a secure, reliable connection that's easy to separate when needed. Each cable is 20cm long wit...
