All Products
Showing 1-20 of 59 products
Kitronik ZIP Halo HD for micro:bit
The Kitronik ZIP Halo HD for micro:bit is the ultimate micro:bit interface. 60 full-colour ZIP LEDs, Pins 1 & 2 broken out, MEMs mic, Piezo sounder, RTC & more!The Kitronik Halo HD board for the BBC micro:bit incorporates 60 individually addressable full colour ZIP LEDs. It also breaks out P1 and...
USB C to 3 USB C Splitter Y Cable 3 USB-C Female Cord Converter 3 Port Hub Charger Power Split Adapter
This USB-C splitter cable converts a single USB-C port into three USB-C female outputs, allowing simultaneous connections for charging, data transfer, and audio. The cable supports USB 2.0 data speeds and Power Delivery (PD) for fast charging across all three ports. Key Features 1-to-3 Splitte...
Servo Y extension cable (300mm)
This 300mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is compatible with almost all of the RC servos.The connectors have gold-flashed conta...
Kitronik Alarm Clock Kit with ZIP Halo HD for micro:bit
Explore time, light, and also sound with the Kitronik Alarm Clock Kit, a fun and hands-on introduction to the ZIP Halo HD. KITRONIK ALARM CLOCK KIT: The Kitronik Alarm Clock Kit with ZIP Halo HD for microbit provides a fun introduction to features of Halo HD. This kit features a modified version ...
Adafruit DS2484 I2C to 1-Wire Bus Adapter Breakout
·
The Adafruit DS2484 is a single-channel I2C-to-1-Wire bus adapter breakout with built-in ESD protection and split supply support. Simply connect it to an existing I2C bus and use the screw terminals to attach DS18B20 temperature sensors or other 1-Wire devices. The 1-Wire protocol, originally de...
NeoPixel RGBW Mini Button PCB - Pack of 10
·
These are the smallest NeoPixel breakouts around! Tiny, bright RGB+White pixels to your project. These little PCBs are only 9.1mm x 9.1mm and have two sets of three pads on the back for soldering wires. These ultra-bright LEDs have a constant-current driver cooked right into the LED package! T...
Industrial RS485 Opto-Isolated Hub
A 4-port RS-485 bus hub with optical isolation and surge protection, designed for industrial environments with complex electromagnetic interference. Each port is independently opto-isolated at 2500 V and protected against 600 W lightning surges, ensuring that a fault on one network segment does n...
SparkFun MicroMod Update Tool
The SparkFun MicroMod Update Tool is built to interface with the MicroMod Asset Tracker Carrier Board and also makes it simple to communicate directly with the u-blox SARA-R510M8S module using u-blox’s sophisticated m-center cellular evaluation software. If you’re familiar with u-center, u-blox’s...
Servo Y extension cable (500mm)
This 500 mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female JR connector connected to two male JR connectors, which means it is compatible with almost all of the RC servos.The connectors have gold-flashed cont...
Snap Action 3-to-9 Wiring Block Connector
·
Snap action wiring blocks make it easy to connect and split wires without soldering, crimping, or tools. This 3-to-9 block has three colour-coded inputs (green, yellow, red), each fanning out to three matching outputs — perfect for basic power or data distribution. Each lever-action terminal acc...
Switching Split Power Supply ± 12V 500mA Split Supply
·
I know you just did a double take when looking at this power supply, what's up with the two cables? Normally you have a switching power supply that plugs into the wall and provides something like 5V or 9V or 12V regulated DC. This split power supply is interesting in that it gives you two power s...
Breadboard - Full-Size (Bare)
A standard full-size solderless breadboard with 830 tie points for prototyping electronic circuits. The two sets of five columns are separated by a 0.3″ channel — perfectly sized for straddling DIP IC packages. Split power buses on each side make it easy to distribute power across your circuit. ...
Small -15 to +15V DC Analog Panel Meter
·
Analog panel meters are arguably not as blingy or flashy as LEDs, but their simplicity adds a touch of elegance and makes them easier to read quickly.This Small -15V to +15V Panel Meter is about handheld-size, with three screws to open up the panel and replace the backing paper, if you like....
Breadboard (400 point)
Solderless breadboard is an essential protoyping tool, allowing you to add push-through components directly onto the board without the need for any soldering. This breaboard comes with two removable "power" rails. The central board is split in half with lines of five points on each half. The boar...
Jumper Jerky - Female to Female
A rainbow-coloured strip of 40 high-quality female-to-female jumper leads with DuPont headers. Each lead is 185mm long and the strip can be easily separated into smaller groups to create custom ribbon cables for your projects. Key Features Type – Female to female (DuPont headers) Quantity – 4...
Miniware DT71 Mini Digital Tweezers
·
The DT71 is a compact set of digital measuring tweezers that combines multifunction component measurement, a miniature waveform signal generator and fully differential input measurement in one portable tool.Its three-section split design includes a controller, measuring arm and tweezer head that ...
Artemis Global Tracker Satellite GNSS Board
·
Built for field deployments well beyond WiFi and mobile coverage, this compact tracker combines an Iridium 9603N Short Burst Data modem with the Arduino-compatible Artemis module. It can send and receive short satellite messages for remote sensing, asset tracking, high-altitude ballooning, ocean ...
Breadboard (830 point)
Solderless breadboard is an essential prototyping tool, allowing you to add push-through components directly onto the board without the need for any soldering. This breaboard has 830 tie points and comes with two removable "power" rails of 100 points each. The central board is split in half with ...
JST SH 9-Pin Cable - 100mm long
·
This 9-pin cable is just about 100mm / 4" long and fitted with JST-SH female connectors on both ends. Compared with chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel and are easy to insert and remove.We got these especially for our fantastically spooky Adafru...
Push-In Wire Connector - 1 Input to 3 Outputs
·
This compact push-in wire connector turns one input connection into three output connections, making it a handy little power distribution tool for low-voltage DC wiring.The internal conductive spring clamp is made from nickel-coated steel for a tight, anti-corrosion grip that is designed to resis...
