All Products
Showing 8441-8460 of 9117 products · 2283 unavailable products hidden
ThinkNode M5 Walkie-Talkie Pro- Meshtastic (LoRa) Signal Transceiver |ESP32-S3 | 1.54” Screen | GPS Function-915 MHz
The Elecrow ThinkNode M5 is a high-performance LoRa communication device powered by the ESP32-S3 processor. Pre-installed with Meshtastic firmware and featuring the SX1262 wireless chip, it efficiently sends and receives LoRa signals for off-grid mesh networking. With its compact, integrated des...
ThinkNode M7 Meshtastic Wireless Communication Gateway, Support PoE Power, Powered By ESP32-S3 and LR1110
This ThinkNode M7 is a high-performance gateway based on the ESP32-S3 module and LR1110 LoRa chip, deeply adapted for the LoRa protocol. The device features an Xtensa 32-bit LX7 dual-core processor with a clock speed of up to 240MHz, providing powerful computing capabilities. It also integrates 2...
Thin Plastic Speaker w/Wires - 8 ohm 0.25W
·
Listen up! This 1.5" diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value). We particularly like th...
Thin Right Angle Ratchet Wrench Set with 9 Bits
Look, over there at that thing! Take it apart! You can now attack just about every kind of box or enclosure that needs undoing with this 9-piece screwdriver set. This kit is of fine quality and excels at disassembling games, phones, cameras, and other small portable electronic goodies.What drew u...
Thin Speaker - 0.5W
If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 0.5W, 8Ohm speaker is only 40mm in diameter and just over 4mm thick, the same kind you might find in one of those "talking greeting cards".
Thin Speaker - 4 Ohm, 2.5W, 28mm
A compact, thin speaker ideal for projects where space is tight. At just 28 mm in diameter and approximately 4 mm thick, it fits into enclosures and wearables where standard speakers won't. The pre-wired 180 mm cable terminates in a 2-pin JST connector for easy hookup. Key Features 28mm Diamet...
Thin White Wheel for TT DC Gearbox Motors - 65mm Diameter
·
We're keepin' it wheel with this one! Plastic gear-box motors (also known as 'TT' motors) are an easy and low cost way to get your projects moving. But we've noticed that there are not a lot of nice TT motor wheels to go along with them. This Thin White Wheel has solid...
Third Hand
This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but soldering flat on a table works just fine. Then again, the desk is starting to loo...
Third Hands
This handy third hand tool helps hold small parts steady while you solder, inspect, glue or assemble detailed projects. It is well suited to electronics work, lab tasks, jewellery making and other precision jobs where an extra pair of hands makes life easier.The heavy iron base keeps the stand st...
Third Hand Soldering Stand
This multifunctional third hand soldering stand combines adjustable crocodile clip clamps, LED lighting, and a dual magnifying lens to keep your hands free while soldering, assembling, or inspecting small components. The weighted base with a steel plate provides extra stability, and it can be po...
Threaded Inserts - 1/4-20 Inch Thread (Pack of 100)
·
These threaded inserts are a handy way to add strong, reusable fixing points to a jig, fixture or machine wasteboard. Place a few exactly where you need hold-down points, or install them in a grid pattern to turn a wasteboard into a threaded table.Installation is straightforward: create a 9mm pil...
Three Phase Brushless Gimbal Stabilizer Motor
A 3-phase DC brushless DC motor has the unique capability of being both a high efficiency, high torque, very smooth motor, as well as the starting point for haptic feedback when combined with the appropriate sensor and motor control. For an excellent demonstration of what's possible with 3-phase ...
Three Wire Display Stand for Raspberry Pi Book IPad or Galaxy
This handy Three Wire Display Stand is made for Raspberry Pi, but also can adapt to other tablet PC, such as iPad. It is great for general electronics & TFT holding. You can adjust the angle as you like. Features Fully adjustable Vinyl Coated Steel Wire that will not scratch furniture or disp...
Threshold Carbon Monoxide Detection Sensor (0-1000ppm)
·
##Introduction This carbon monoxide gas sensor differs from most gas sensors on the market as it does not provide specific gas concentration data. Instead, it detects whether the surrounding environment exceeds or falls below a fixed threshold. It operates on a wide voltage range of 5-24V, with h...
Threshold Formaldehyde HCHO Detection Sensor (0-20ppm)
·
##Introduction This formaldehyde gas sensor differs from most gas sensors on the market as it does not provide specific gas concentration data. Instead, it detects whether the surrounding environment exceeds or falls below a fixed threshold. It operates on a wide voltage range of 5-24V, with high...
Through Hole Dual Inline Pogo Pin Header - 2x3 with 0.1" Spacing
·
Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also if say you want to JTAG program a board that you can't solder headers to.Most pog...
Through Hole Inline Pogo Pin Header - 9 Pins with 0.1" Spacing
·
Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also if say you want to JTAG program a board that you can't solder headers to.Most pog...
Through-Hole Resistors - 100K ohm 5% 1/4W - Pack of 25
·
A pack of 25 through-hole 100 kΩ resistors — an essential component for voltage dividers, pull-up/pull-down circuits, and general electronics projects. The 0.4 mm lead diameter fits standard solderless breadboards perfectly. Specifications Resistance – 100 kΩ Tolerance – ±5% Power Rating – ¼...
Through-Hole Resistors - 10K ohm 5% 1/4W - Pack of 25
·
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 10K Ω Resistors. More specifically, they are carbon film, through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% pre...
Through-Hole Resistors - 1.0K ohm 5% 1/4W - Pack of 25
·
ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you!This is a 25 Pack of 1.0KΩ Resistors. More specifically, they are carbon film, through-hole axial type, with 1/4 Watt max dissipation, 300V max voltage, 5% precision resistor...
