All Products

SKU: SF-BOB-09816

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets the signal level between the stages, not the feedback path. The bandwidth is set to 15.9kHz by a pair of feedback capacitors, or over 100kHz with the...

SKU: SF-DEV-13712

The SparkFun OpenLog is an open-source serial data logger based on the ATmega328 running at 16 MHz. It logs incoming serial data directly to a microSD card, supporting cards from 64 MB to 64 GB in FAT16 or FAT32 format. Simply connect a serial line from your project to the OpenLog, and all transm...

SKU: SF-DEV-19426

The SparkFun OpenLog Artemis (OLA) is an open-source data logger built on the Artemis module (Cortex-M4F Apollo3 microcontroller). It comes pre-programmed to automatically detect, configure, and log data from Qwiic-enabled sensors — no coding required. Simply plug in a compatible sensor, power up...

SKU: SF-KIT-20684

The Air Quality Monitoring version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data from an included SGP40 Qwiic Air Quality Sensor with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an open source data ...

SKU: SF-KIT-20673

The Base version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an open source data logger that comes preprogrammed to automatically log GPS / GNSS, s...

SKU: SF-KIT-20683

The Environmental Monitoring version of the SparkFun OpenLog Data Collector Kit with Machinechat is an easy way to organize and display your data from an included BME280 Qwiic Atmospheric Sensor with the OpenLog Artemis and JEDI One. The SparkFun OpenLog Artemis (without IMU) is an open source da...

SKU: SF-BOB-09118

This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two pho...

SKU: SF-TOL-11640

When you’re working with e-textiles, you have a tendency to collect a lot of small parts: LilyPad boards, bobbins, needles, the tools of the trade. Why not pick up a sturdy little box to keep your bits and pieces off the floor? This LilyPad branded box is made from rigid cardboard printed with a ...

SKU: SF-TOL-15295

One ruler to rule them all. This is a basic 12 inch ruler, but made from a PCB. We have included a lots of useful information on each side of the ruler that you might use on a daily basis including Wire Gauge holes, transistor diagrams, common fractions, Roman numerals, and metric to imperial con...

SKU: SF-SEN-22956

The SparkFun Photoacoustic Spectroscopy CO2 Sensor features the Infineon XENSIV PAS CO2 (PASCO2V01) sensor, which delivers highly accurate CO2 measurements in direct parts-per-million (ppm) format. The photoacoustic spectroscopy system combines narrow-band filtered IR light with a sensitive micro...

SKU: SF-SEN-16474

The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light that is...

SKU: SF-BOB-09322

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or an...

SKU: SF-DEV-13321

The SparkFun Photon RedBoard, to put it simply, is a WiFi/Microcontroller development board in the Arduino form-factor for the Photon. It’s easy to use, it’s powerful, and it’s connected to the cloud. With the best support, potential, and performance the Photon RedBoard provides you with an IoT d...

SKU: SF-KIT-13863

The SparkFun PicoBoard Starter Kit is your go-to source to begin learning everything about the SparkFun PicoBoard and the Scratch programming environment. This kit includes your very own PicoBoard, multiple pieces of hardware to get you started, and connecting components to get you hooked up. ...

SKU: SF-SEN-17372

Passive Infrared (PIR) sensors are great for detecting motion in a small area around the sensor. The 170µA SparkFun EKMC4607112K PIR Breakout is a simple board equipped with an EKM-series PIR sensor from Panasonic®. The EKM-series PIR sensors are optimized for small movements to offer motion-sens...

SKU: SF-KIT-19519

The SparkFun 170uA PIR Breakout Starter Kit comes with everything you need to get started using Passive Infrared (PIR) sensors. PIR sensors are great for detecting motion in a small area around the sensor. The 170µA SparkFun EKMC4607112K PIR Breakout is a simple board equipped with an EKM-series ...

SKU: SF-KIT-19518

The SparkFun PIR Breakout Starter Kit includes everything needed to get started with passive infrared motion detection. Built around the Panasonic EKMB1107112 PIR sensor, this kit's breakout board offers ultra-low 1µA standby current, making it ideal for battery-powered motion-sensing application...

SKU: SF-BOB-13717

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decoupling capacitors on the power supply lines. The “Wedge” also makes the initial b...

SKU: SF-KIT-14526

The Pi Zero USB Stem is a PCB kit that turns a Raspberry Pi Zero into a USB dongle. Once the Stem is installed, your Raspberry Pi can be plugged directly into a computer or USB hub without any additional cables or power supplies. The Raspberry Pi then acts as a USB device using its own Linux kern...

SKU: SF-DEV-15801

The SparkFun Power Delivery Board uses the STMicroelectronics STUSB4500 controller to negotiate USB Power Delivery (PD) contracts with compatible chargers and adapters. Instead of being limited to 5 V from a standard USB connection, this board can request higher voltages — typically 5–20 V and up...