Adafruit
64x64 RGB LED Matrix Panel with 45 Degree Curb-Cut - 2.5mm Pitch
The 64×64 RGB LED Matrix Panel with 45° Curb-Cut corners and 2.5mm pitch features 4096 bright RGB LEDs in an ultra-high-density panel. The curb-cut corners a...
The 64×64 RGB LED Matrix Panel with 45° Curb-Cut corners and 2.5mm pitch features 4096 bright RGB LEDs in an ultra-high-density panel. The curb-cut corners are angled at 45°, allowing multiple panels to be assembled into LED video cubes or rectangular enclosures with seamless edges.
This panel uses a non-standard 5-address (ABCDE) multiplexing system. Many standard drivers only support 4-address (ABCD) setups. Compatible controllers include the RGB Matrix Bonnet for Raspberry Pi, RGB Matrix HAT (both require a solder jumper), and Matrix Portal (jumper required). Arduino shields with the Adafruit library and HDMI driver boards do not support 5-address multiplexing. The SmartLED Shield with Teensy 3.5/3.6 has the hardware for 5-address panels and sufficient RAM, but the power plug must be manually soldered or adapted due to shield overlap.
Key Features
- 45° Curb-Cut Corners – Angled edges allow panels to be assembled into cubes and rectangular enclosures
- 2.5mm Pixel Pitch – Ultra-high density for sharp detail at close viewing distances
- 4096 RGB LEDs – 64×64 resolution with full-colour output
- 5-Address Multiplexing – ABCDE system for 64-pixel tall panels
- Chainable – IDC input/output connectors allow multiple panels to be daisy-chained
Specifications
- Pixel Pitch: 2.5mm
- Resolution: 64×64 (4096 LEDs)
- Operating Voltage: 5V
- Corner Cut: 45°
Also Available
- 64×64 RGB LED Matrix Panel – 2mm Pitch
- 64×64 RGB LED Matrix – 2.5mm Pitch
- 64×64 RGB LED Matrix – 3mm Pitch
- 64×64 RGB LED Matrix Panel – 3mm Pitch (DFRobot)
Ideal For
- LED video cubes and rectangular display enclosures
- Multi-panel installations requiring seamless corners
- Close-range indoor displays and signage
- Raspberry Pi projects using the RGB Matrix Bonnet or HAT
Package Contents
- 1× 64×64 RGB LED Matrix Panel with 45° curb-cut corners (2.5mm pitch)
- 1× IDC ribbon cable
- 1× Power cable
Jargon buster
Plain-language definitions for the technical terms used above.
- HDMI
- HDMI is a common digital video and audio connection used by computers, media players, and many displays. If a display kit has HDMI input, it is usually much easier to test with a single-board computer because it can act like a normal monitor.
- LED
- A light-emitting diode is a small electronic component that lights up when current flows through it in the correct direction. In this kit, LEDs create the flashing effect, so polarity and correct soldering matter for the project to work.
- RAM
- RAM is temporary memory used while a device is running, and its contents are lost when power is removed. A “Run in RAM” mode is useful for testing settings without permanently programming the module, but it may not support every feature.
- RGB
- Short for red, green and blue, usually referring to an LED that can mix those three colours. It matters because controlling an RGB LED teaches how separate outputs combine to create different colours.
- Shield
- An add-on board that plugs into a main controller board to give it extra features such as sensing, motor control or communication. Knowing a product supports shields helps you judge whether it can connect neatly into an existing maker-board setup.
- solder jumper
- A solder jumper is a small pair or group of pads on a circuit board that can be bridged or cut with solder to change a hardware setting. It matters because changing modes may require careful soldering rather than just changing software.
Find this product in
Brands
Displays & Screens
Related Tutorials
Free guides on learn.littlebird.com.au
