Wearables & E-textiles

SKU: PL-1696 | Brand: Pololu

This force-sensing resistor (FSR) from Interlink Electronics is a passive component that exhibits a decrease in resistance when there is an increase in the force applied to the 0.58″-diameter (1.5 cm) active area...

SKU: AF-615 | Brand: Adafruit

This gold-eye sharps needle set is perfect for hand-sewing with conductive thread and wearable electronics parts. The pack includes 20 needles in sizes #3 to #9, giving you the right needle for any e-textiles or gener...

SKU: AF-2328 | Brand: Adafruit

Adafruit DotStar LED strips use 2-wire SPI instead of the single-wire protocol used by NeoPixels, allowing much faster data rates (up to 32 MHz) and a 20 KHz PWM refresh rate. This makes DotStars ideal for persistence...

SKU: LW-TEK6 | Brand: Little Bird

Teknikio Blue star-shaped sewable LED board.  Product Details• Add light up LED Stars to your crafts• LED light is blue• Pack Includes 4x LED Stars• Recommended Age 8+

SKU: AF-2239 | Brand: Adafruit

The Adafruit DotStar Digital LED Strip (60 LED/m, black flex PCB) delivers superior performance over traditional NeoPixels with its 2-wire SPI interface. Push data at up to 32 MHz clock speed with no critical timing r...

SKU: SF-KIT-13927 | Brand: SparkFun

The LilyPad Sewable Electronics Kit is an introduction to the world of e-textiles and electronic sewing. Through a series of guided projects, you'll learn to sew basic circuits, light up LEDs, control them with button...

SKU: SF-DEV-13902 | Brand: SparkFun

This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up.LilyPad is a wearable e-t...

SKU: AF-653 | Brand: Adafruit

This sewable CR2032 battery holder makes it easy to add power to wearable electronics projects. Two small 1mm holes in the metal connection tabs are perfectly sized for a #5 or smaller needle to pass through, so you c...

SKU: AF-4429 | Brand: Adafruit

This 13.56 MHz RFID/NFC sewable button uses an NTAG213 chip in a compact 24 mm laundry-tag form factor. It can be sewn into garments, attached to equipment, or embedded in projects for contactless identification, data...

SKU: KI-2715 | Brand: Kitronik

A starter kit for e-textiles and wearable electronics from Kitronik's Electro-Fashion range. This Discovery Pack includes a curated selection of sewable components — LEDs, switches, coin cell holders, conductive threa...

SKU: PI-TEK004 | Brand: Pimoroni

A four pack of sewable, heart-shaped bright pink LEDs. The voltage (and hence current) supplied from LIR2032 rechargeable coin cell batteries may damage the Teknikio LED boards, so please ONLY USE CR...

SKU: LB-LR0309-45 | Brand: Little Bird

A 1-metre length of soft conductive sewing thread made from stainless steel, designed for wearable electronics projects. Use it to sew electrical connections between LilyPad components, sewable LEDs, and batteries — r...

SKU: AF-588 | Brand: Adafruit

A starter pack containing 2.5 metres of high-brightness pink EL (electroluminescent) wire with a pocket inverter and soldering supplies. The EL wire comes pre-cut and soldered, ready to connect to the included battery...

SKU: AF-1481 | Brand: Adafruit

This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand, it's just a gigantic resistor. On the other hand, it's flexible,...

SKU: SF-DEV-14546 | Brand: SparkFun

The LilyPad E-Sewing ProtoSnap is a great way to explore how buttons and switches behave in simple e-sewing circuits before crafting your project. Like other LilyPad ProtoSnap series boards, the individual pieces of t...

SKU: DF-SEN0086 | Brand: DFRobot

A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power G...

SKU: DF-DFR0167-R | Brand: DFRobot

LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn ...

SKU: DF-DFR0167-G | Brand: DFRobot

A pack of five green LEDs designed for the LilyPad wearable electronics platform. Each LED is mounted on a thin, sewable PCB with large connecting pads, making it easy to stitch into clothing and e-textile projects wi...

SKU: AF-408 | Brand: Adafruit

EL Wire, also known as Electroluminescent wire is a stiff wire core coated with phosphor and then covered with a protective PVC sheath. When an AC signal is applied to it, it glows an aqua (blue green) color. You c...

SKU: AF-625 | Brand: Adafruit

This electroluminescent (EL) panel produces an even, diffused glow across its entire 10 × 10 cm surface. It's the flat equivalent of EL wire — a flexible sheet of plastic coated with EL material that emits a soft, uni...