SparkFun Qwiic Ecosystem

SKU: AF-4424 | Brand: Adafruit

A 200mm adapter cable with a JST-SH 4-pin connector (STEMMA QT / Qwiic, 1mm pitch) on one end and a JST-PH 4-pin connector (STEMMA / Grove, 2mm pitch) on the other. Use it to bridge I2C sensors and drivers between the...

SKU: AF-5384 | Brand: Adafruit

This 300 mm (11.8") 4-wire cable is fitted with JST-SH female 4-pin connectors on both ends. The 1 mm pitch JST-SH connectors are more compact than the chunkier 2 mm pitch JST-PH, while still providing a secure latchi...

SKU: AF-4210 | Brand: Adafruit

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching f...

SKU: SF-PRT-17260 | Brand: SparkFun

This is a 50mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon m...

SKU: AF-4401 | Brand: Adafruit

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching fe...

SKU: PI-PIM724 | Brand: Pimoroni

A top of the line Pirate-brand RP2350 microcontroller with 16MB of flash memory, 8MB of PSRAM, USB-C, Qw/ST and debug connectors.We adore the versatility and value of Raspberry Pi Pico but we also enjoy a souped up RP...

SKU: SF-DEV-14495 | Brand: SparkFun

The SparkFun Qwiic Adapter provides the perfect means to make any old I2C board into a Qwiic-enabled board. This adapter breaks out the I2C pins from the Qwiic connectors to pins that you can easily solder with you...

SKU: SF-PRT-17258 | Brand: SparkFun

This is a 200mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon mak...

SKU: SF-PRT-17259 | Brand: SparkFun

This is a 100mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon mak...

SKU: SF-DEV-15794 | Brand: SparkFun

The SparkFun Qwiic SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a Qwiic connector to your Raspberry Pi. The SHIM design allows you to plug directly to the Pi's I2C bus with no soldering...

SKU: SF-DEV-15123 | Brand: SparkFun

The SparkFun RedBoard Qwiic is an Arduino-compatible development board in the UNO R3 form factor with a built-in Qwiic connector for solderless I2C hookup. It programs over USB Micro-B using the Arduino IDE — select "...

SKU: SF-DEV-15795 | Brand: SparkFun

Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The SparkFun Qwiic Pro Micro is a revision of the original Pro Micro a...

SKU: SF-PRT-17257 | Brand: SparkFun

This is a 500mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. The cable insulation is made from silicon mak...

SKU: SF-DEV-17156 | Brand: SparkFun

An extended Qwiic shield that adds four Qwiic connectors to Teensy 4.1, Teensy 3.6, and Teensy 3.5 boards. Connects the I²C bus (GND, 3.3 V, SDA, SCL) to two horizontal and two vertical Qwiic ports for easy daisy-chai...

SKU: AF-4208 | Brand: Adafruit

A 10-pack of JST SH 4-pin right-angle connectors with 1 mm pitch through-hole mounting tabs. These are the standard connectors used with the Qwiic and STEMMA QT ecosystems, making it easy to add I2C connectivity to yo...

SKU: SF-SEN-19096 | Brand: SparkFun

The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The ga...

SKU: SF-DEV-17047 | Brand: SparkFun

The SparkFun Qwiic GPIO adds eight additional digital I/O pins to your project via I2C, based on the TCA9534 I/O Expander from Texas Instruments. Read and write pins just like standard Arduino digital pins using the i...

SKU: SF-SEN-16295 | Brand: SparkFun

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junc...

SKU: SF-BOB-15931 | Brand: SparkFun

Buttons are an easy and tactile way to interface with your project, but why would you want to deal with debouncing, polling, and wiring up pull-up resistors? The SparkFun Qwiic Button Breakout simplifies all of those ...

SKU: SF-PRT-14417 | Brand: SparkFun

Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of our Qwiic-based boards and can be used to create your own I2C-based device compatible with the Qwiic system!Additionally, this connector w...