Prototyping

SKU: DF-DFR0140 | Brand: DFRobot

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. It can be either powered from 6-12...

SKU: SF-COM-10969 | Brand: SparkFun

Resistors are a good thing, in fact, they’re actually crucial in a lot of circuit designs. The only problem seems to be that resistors disappear into thin air. The only way to be sure that you’re gonna have the res...

SKU: SF-PRT-12795 | Brand: SparkFun

These are 6" long jumper wires with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Combine these with our female to female jumpers to create a mal...

SKU: AF-3351 | Brand: Adafruit

Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like this speaker as it is small...

SKU: SF-PRT-10007 | Brand: SparkFun

A set of stackable headers designed for the Arduino Uno, Arduino Pro, and other boards using the classic (pre-R3) pin layout. These female headers sit tall enough to clear the USB-B connector, making them ideal for st...

SKU: AF-4210 | Brand: Adafruit

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching f...

SKU: AF-290 | Brand: Adafruit

Perfect for bread-boarding, free wiring, etc. This spool of solid-core wire is easy to solder to. When bent it keeps its shape pretty well. We like to have a few spools of this stuff around. We suggest picking up wire...

SKU: AF-356 | Brand: Adafruit

These are our favorite trim pots, perfect for breadboarding and prototyping. They have a long grippy adjustment knob and with 0.1" spacing, they plug into breadboards or perfboards with ease. This is the same pot t...

SKU: LB-LR0293-29 | Brand: Little Bird

These compact jumper cables feature a premium female header on one end and a grippy mini alligator clip on the other — perfect for breadboarding with non-header-friendly boards and components. Clip onto a micro:bit, C...

SKU: SF-PRT-12044 | Brand: SparkFun

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumpe...

SKU: AF-64 | Brand: Adafruit

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to...

SKU: SF-DEV-11235 | Brand: SparkFun

The Arduino and Breadboard Holder is a sturdy plastic base plate that keeps your Arduino and breadboard neatly organised during prototyping. The board mounts with two included screws using the standard Arduino mountin...

SKU: AF-1950 | Brand: Adafruit

Premium female-to-female jumper wires in a convenient 20-pin ribbon cable, perfect for making wire harnesses or jumpering between headers on PCBs. Each wire is 150mm (6") long with 0.1" (2.54mm) female header contacts...

SKU: AF-2310 | Brand: Adafruit

The Adafruit Perma-Proto HAT for Pi Mini Kit is a full-sized prototyping daughter board for any Raspberry Pi with a 2×20 GPIO header (Pi Zero, A+, B+, Pi 2, 3, 4, 5). It provides a grid of 0.1″ soldering holes connect...

SKU: SF-COM-10926 | Brand: SparkFun

A 1N5819 Schottky diode rated at 1A and 40V. Schottky diodes are characterised by their low forward voltage drop (typically ~0.3V) and very fast switching speed, making them ideal for flyback protection on motor drive...

SKU: DF-FIT0080 | Brand: DFRobot

A 4-cell AA battery holder in a square (2×2) configuration with a sliding removable cover and a built-in ON/OFF switch. Features 5-inch tinned leads for easy soldering. The cover keeps batteries secure, and the switch...

SKU: DF-DFR0831 | Brand: DFRobot

INTRODUCTIONThis is a 20W DC-DC buck converter power module with 7~24V input and 5V/4A output(Max). The high conversion efficiency and on-board 6 output ports make it suitable for connecting multiple devices like, lar...

SKU: SF-TOL-09327 | Brand: SparkFun

Solder wick (also known as desolder braid) is made from braided copper threads treated with flux. When placed over an unwanted solder joint and heated with a soldering iron, the flux activates and draws the molten sol...

SKU: SF-COM-08375 | Brand: SparkFun

This is a very common 0.1uF capacitor. Used on all sorts of applications to decouple ICs from power supplies. 0.1" spaced leads make this a perfect candidate for breadboarding and perf boarding. Rated at 50V. If y...

SKU: SF-COM-08285 | Brand: SparkFun

A pack of super bright green LEDs in the standard 5 mm (T1¾) package with clear lenses. At 12,000 mcd, these LEDs deliver exceptional brightness suitable for indicators, lighting effects, and high-visibility projects....