Prototyping

SKU: SF-PRT-08100 | Brand: SparkFun

Individual crimp pins for use with polarized connector housings. These pins prevent incorrect or reversed connections, making them ideal for power, sensor, and general-purpose wiring on perfboard and PCB projects. At...

SKU: SF-PRT-08097 | Brand: SparkFun

Polarized connectors and headers for your perf board/PCB projects. Use these connectors for power connections or any sensor/general connection to prevent users from connecting the peripheral incorrectly or reversed. T...

SKU: SF-COM-00540 | Brand: SparkFun

Standard ‘Watch’ or Real-Time-Clock crystal. 32.768kHz means it is precisely half of a 16-bit counter. Start counting at 0x8000 (or 32768). When the counter rolls over from 65535 to 0, then you know that exactly one s...

SKU: SF-BOB-00496 | Brand: SparkFun

The SparkFun SOIC to DIP Adapter converts 28-pin SOIC surface-mount packages to standard 0.1" through-hole headers, making it easy to prototype with SMD ICs on breadboards or in DIP sockets. Key Features 28-Pin SOI...

SKU: SF-PRT-11269 | Brand: SparkFun

This pack of female headers includes two 6-pin headers and two 8-pin headers. This is similar to the header kit that comes with Arduino shields except that the pins are shorter so they don’t stack. These are useful fo...

SKU: SF-KIT-13053 | Brand: SparkFun

Holy Wattage, Batman! This Power Resistor Kit comes with 5 each of 5 different 10 Watt resistor values including 1, 2, 4, 8, and 16 Ohms. These resistors are capable of dissipating large amounts of power without damag...

SKU: SF-PRT-12791 | Brand: SparkFun

This is a 2x23 pin male PTH header. This piece is in the common configuration for Beaglebone Black headers that can be broken apart to form smaller header formations. Each pin has a spacing of 0.1" in between each oth...

SKU: SF-PRT-10359 | Brand: SparkFun

This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on ...

SKU: SF-PRT-12718 | Brand: SparkFun

PCB mount clip to hold a AAA battery. Sold in single units, you’ll need two for each battery. These work great for small, low power applications that need a battery to run. Low cost and easy to use!Documents:Datasheet

SKU: SF-BOB-12708 | Brand: SparkFun

This is the SparkFun Real Time Clock (RTC) Module, this little breakout that uses the DS1307 to keep track of the current year, month, day as well as the current time. The module comes fully assembled and includes a s...

SKU: DF-FIT0475 | Brand: DFRobot

This plywood case is a solid enclosure for your LattePanda Windows 10 SBC. The case protects the board from ESD damage while letting you see status LEDs and providing access to USB, HDMI, SD card, GPIO and anten...

SKU: SF-PRT-09387 | Brand: SparkFun

A pack of 10 premium male-to-male jumper wires, 12" (30cm) long. Compatible with breadboards, Arduino headers, and any 0.1" (2.54mm) pitch prototyping board. Assorted colours for easy circuit identification. Specific...

SKU: SF-PRT-09388 | Brand: SparkFun

This is a SparkFun exclusive! These are 12" long jumper wires terminated as male to male. Use these to jumper from any female header on any board. Multiple jumpers can be connected next to one another on a 0.1...

SKU: AF-2120 | Brand: Adafruit

If you've started designing your own PCBs in Eagle or KiCad and want to make your PCB a reality, you may start out with an etching system to pattern out traces. But that's only half the job! You'll also need a way ...