Prototyping

SKU: LB-LR0589-GREEN | Brand: Little Bird

A 12 mm panel-mount momentary push button with a smooth dome-shaped cap in green. Normally open — pressing the button closes the contacts. The dome design provides a satisfying tactile feel and sits flush with the pan...

SKU: DF-FIT0720 | Brand: DFRobot

These patch test hooks provide a solderless way to make signal and low-current connections between boards, sensors, and modules. The hook clips grab onto pins, pads, and component legs — perfect for prototyping with c...

SKU: LB-LR0382 | Brand: Little Bird

A 4-position DIP switch with standard 2.54mm (0.1") pitch, suitable for through-hole mounting on PCBs, perfboard, and breadboards. Each of the four switches can be independently toggled on or off, making it useful for...

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: LB-LS1216 | Brand: Little Bird

This sensor is composed of an infrared emitter on one upright and a shielded infrared detector on the other. By emitting a beam of infrared light from one upright to the other, the sensor can detect when an object pas...

SKU: LB-LS0070 | Brand: Little Bird

The knob is designed to set directly on the potentiometer's ridges so it's an easy & secure fit. It has a nice feel, with a solid grip, tweaking it is quite fulfilling This is the red version and it has a nice deep...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2193 | Brand: Adafruit

A 10-pack of 100µF 16V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic ...

SKU: SF-BOB-09056 | Brand: SparkFun

A breakout board for the CD74HC4067 16-channel analogue/digital multiplexer/demultiplexer. This IC internally routes a common signal pin (SIG) to one of 16 channel pins, working with both analogue and digital signals ...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: SF-PRT-11895 | Brand: SparkFun

A standard 8-pin female header with 0.1" (2.54 mm) pitch, designed for through-hole mounting. Connects with most standard 8-pin male headers. Specifications Pins – 8 Pitch – 0.1" (2.54 mm) Type – Female, through-...

SKU: SF-COM-11144 | Brand: SparkFun

A ¼″ (6.35mm) stereo audio jack in a right-angle panel-mount configuration. Switched contacts allow you to detect whether a plug is inserted. The jack mounts in an 11mm diameter panel hole and includes a plastic washe...

SKU: SF-COM-13014 | Brand: SparkFun

This is a 3-terminal microswitch two pack, each equipped with a 20mm offset lever actuator. These switches have a great ‘clicky’ sound to them with a nice tactile feel and are perfect when used for a slider, 3D pri...

SKU: AF-550 | Brand: Adafruit

Small self-adhesive rubber bumper feet for electronics boards and devices. Stick them to the bottom of any PCB to protect your desk, prevent sliding, and provide clearance for through-hole solder joints underneath. T...

SKU: SF-PRT-12693 | Brand: SparkFun

This is a row of 40 break away headers spaced 0.1" apart with long pins on both sides. This header is especially useful when you need to connect a PCB to a solderless breadboard. Each header can be broken apart to ...

SKU: AF-1951 | Brand: Adafruit

These premium female-to-female jumper wires are ideal for making wire harnesses or connecting between headers on PCBs. Each pack contains 20 wires in a ribbon cable format — two of each of ten rainbow colours — that c...

SKU: LB-LS4650 | Brand: Little Bird

This flat, dense PCB holder is designed to keep your circuit board steady while you work. Its low-profile vise style lets your hands rest directly on the work table, making it easier to steady yourself during precise ...

SKU: AF-5617 | Brand: Adafruit

Snap action blocks are perfect when you have to quickly wire up a bunch of free-hanging components, and you don't want to solder. They're much easier to use than wire nuts, and of course, they are reuseable and do not...

SKU: AF-5359 | Brand: Adafruit

If you love power adapters or toys & gadgets that have magnetic connections, you can now experiment with these futuristic connectors easily. It's sorta like a DIY "MagSafe-styled" connector, with five 0.1" spaced cont...