Prototyping & Wiring

SKU: SF-CAB-11604 | Brand: SparkFun

USB On-The-Go is a really useful USB specification! It allows some small devices that would usually be unable to act as a host to have limited hosting capabilities! USB-OTG is common for things like tablet computers a...

SKU: DF-DFR0016 | Brand: DFRobot

This is a design for an open-source prototyping shield for Arduino Mega. It has tons of cool features, to make prototyping on your Arduino easy. Some assembling and soldering is required! Some assembling and s...

SKU: AF-3071 | Brand: Adafruit

The Adafruit RFM69HCW Transceiver Radio Breakout @ 433 MHz is a breadboard-friendly packet radio module for adding long-range wireless communication to Arduino and other microcontroller projects. Based on the SX1231 t...

SKU: SF-SEN-13715 | Brand: SparkFun

This is a stainless steel, Type-K Thermocouple probe. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the othe...

SKU: SF-DEV-13712 | Brand: SparkFun

The SparkFun OpenLog is an open-source serial data logger based on the ATmega328 running at 16 MHz. It logs incoming serial data directly to a microSD card, supporting cards from 64 MB to 64 GB in FAT16 or FAT32 forma...

SKU: SF-COM-13699 | Brand: SparkFun

The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that allows additional inputs or outputs to be added to a microcontroller by converting data between parallel and serial...

SKU: SF-PRT-11475 | Brand: SparkFun

A robust 6-pin GX16 aviation-style connector set including both the panel-mount jack and mating plug. The threaded locking ring screws onto the panel connector, creating a secure connection that won't pull apart — ide...

SKU: AF-166 | Brand: Adafruit

The Interlink 402 is a round force-sensitive resistor (FSR) with a 12.7 mm (0.5″) sensing area. It changes resistance based on applied pressure — the harder you press, the lower the resistance — making it a simple, lo...

SKU: SF-COM-11451 | Brand: SparkFun

These color-changing LEDs take the work out of creating crazy, flashy, blinky… ness. Simply apply power and the LED will cycle through the RGB colorspace: no external controller necessary! These bright and festive ...

SKU: DF-SEN0170 | Brand: DFRobot

A three-cup anemometer kit with 0–5V analog voltage output for building custom weather stations and wind monitoring systems. The aluminium alloy construction provides high strength, weather resistance, and corrosion r...

SKU: AF-3133 | Brand: Adafruit

The Adafruit Ultimate GPS FeatherWing brings precise, low-power GPS to the Feather ecosystem. Built around the MTK3339 chipset, it tracks up to 22 satellites on 66 channels with -165 dBm sensitivity and delivers up to...

SKU: AF-238 | Brand: Adafruit

This is a interface cable designed for Bus Pirate which can makes it easier to connect the Bus Pirate to a circuit and get hacking!

SKU: SF-BOB-13601 | Brand: SparkFun

Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/...

SKU: AF-3083 | Brand: Adafruit

A compact aluminium heatsink with pre-applied thermal adhesive for easy installation on the Raspberry Pi 3 and other single board computers. Simply peel off the protective film and press firmly onto the processor — no...

SKU: SF-PRT-11366 | Brand: SparkFun

This is the Big Red Box! These beefy, bright red, flanged, plastic enclosures will give your widget the protection (and attention) it deserves. You’ve probably seen these used to enclose radio equipment or antenna bal...

SKU: SF-PRT-11363 | Brand: SparkFun

A set of three common gauges of enameled magnet wire for winding transformers, chokes, motors, and electromagnet experiments. The thin enamel coating insulates each wire, allowing tight coil windings without short cir...

SKU: SF-COM-11289 | Brand: SparkFun

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.These hea...

SKU: PL-1076 | Brand: Pololu

This M3, pan-head screw is 8 mm long. It is made from steel, is zinc-plated, and comes in packs of 25.

SKU: AF-3119 | Brand: Adafruit

This HDMI plug breakout board lets you create custom HDMI cables or tap into individual HDMI pins for specialised wiring setups. The solid PCB features an HDMI plug with through-hole pads for soldering your own connec...

SKU: AF-3122 | Brand: Adafruit

Make your own custom DE-9 cable or DE-9 interface with ease, using this DE-9 Socket to Terminal Block Breakout. You get a nice solid PCB with an DE-9 socket and two strips of terminal blocks that you can use with stra...